background image

Thermionic Culture Ltd, October 2019 

1

 

 

WARNING 

 

For your personal safety, please read this operating manual and 
warning thoroughly before using the equipment. 
 
This  unit  must  be  installed  in  such  a  manner  that  operator 
access to the mains plug is maintained. Where the product is to 
be rack mounted, this may be achieved by having access to the 
disconnection device for the whole rack. 
 
To reduce the risk of electric shock, it is essential that the unit 
is  disconnected  from  the  mains  supply  before  removing  the 
cover. 
 
Please  also  note  that  the  power  supply  capacitors  within  this 
unit can remain charged even after the mains supply has been 
disconnected.  It  is  essential  that  these  capacitors  are 
discharged after the mains supply has been disconnected and 
the covers have been removed. 
 
In the event that this unit has been dropped or has suffered an 
impact,  an  electrical  safety  test  must  be  carried  out  before 
reconnection to the mains supply. 
 
This  equipment  is  not  intended  for  use  in  explosion  hazard 
environments. It must be used and stored in studio conditions, 
such that the ambient relative humidity does not exceed 80%, 
nor is the temperature to be allowed to drop to a level, which 
would cause dew point to be reached. 
 
It is not advisable to operate this equipment if all valves are not 
in place and working, as voltages will rise and components may 
overheat and fail. 

 

Summary of Contents for Snow Petrel














Reviews: