Page 2
123
123
123
➛
➛
Minimum Clear-
ance 1-3/8"
➛
➛
➛
➛
➛
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
➛
Minimum 3" Length
of 3-1/4" x 10"
➛
*Damper Collar for
3-1/4" x 10" duct
➛
➛
Recommended
Depth 4-1/4"
Minimum
Minimum Clear-
ance 3/4"
}
}
VERTICAL
DISCHARGE
HORIZONTAL
DISCHARGE
*To Bottom of
Damper Collar
1-1/4"
Fig. 2
DUCTING FOR VCK300
1.
Use the Transition #1255-17 when 7" round Duct is used.
2.
Finish with Roof Jack #1255-6 or Wall Cap #1255-1. Make sure all
dampers are free to open.
3.
Be sure the 3-1/4" x 10" knockout on the housing body is REMOVED
before attaching the damper collar.
* Damper Collar and two Ventilator motor support bolts and nuts are
shipped with the VCK300.
DUCTING FOR VR1000 & VR600
To adapt this VCK-1 unit for installation with the VR1000 a Transition #1308-
10 and a 10" round duct must be used. For installation with the VR600 a
Transition #1308-8 and an 8" round duct must be used. Before installing
VCK-1 in hood or cabinet attach transition to top of VCK1 through holes with
screws provided.
IMPORTANT
: Be sure the 8" x 13" knockout on the top of the housing body is
removed before attaching the Transition.
DUCTING FOR VCK300
(For ventilator motor mounted inside of
ventilator housing)
VCK1 with VCK300 (Integral Blower), VR600 or VR1000 (Remote Blower)
these installations must meet all local code requirements.
1.
Unless otherwise required by compliance with local codes, recom-
mended installation height from countertop to VCK1 mounting surface
over counter level range, cooktop, 30" to 34", over indoor barbecue 34" to
48".
2.
Cut a 9-3/4" x 19" opening in the bottom of the cabinet or hood to allow
for the ventilator body (see figures 2 and 3 for minimum clearance).
Fig. 3
DUCTING FOR THE VR600 & VR1000
(
Vertical Discharge only)
10" Diameter Duct for VR1000
8" Diameter Duct for VR600
(Duct NOT supplied)
➛
➛
Transitions:
For VR1000 - #1308-10
For VR600 - #1308-8
•
Transition Height 10-1/4"
Minimum Clearance 1-3/8"
➛
➛
12345
12345
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
Mounting Surface
➛
➛
Recommended
Depth 4-1/4"
➛
➛
Mounting Bolts
are installed in
forward position
Vertical
Discharge
VERTICAL HORZONTAL
Mounting Bolts
are installed in
rear position for
Horzontial
Discharge
Front
➛
9-3/4" x 18-3/8"
Cutout
➛
12
12
123
123
123
123
123
123
123
123
123
123
123
123
➛
➛
➛
➛
10-1/2"
➛
Absolute
Minimum
10-1/2"
Transitions:
For VR1000 -
#1308-10
For VR600 -
#1308-8
•
Absolute
Minimum
DUCTING FOR KITCHEN CABINET INSTALLATION
VCK300
VR600 & VR1000
3/4" required
for Clearing
Collar for
Horizontal
Discharge
Fig. 5
Fig. 4
Safety Warning
: Turn off proper circuit at the service entrance and lockout panel
before wiring this unit.
3.
VCK300 ONLY
- Attach power supply leads (120 volts, 60 Hz.) in
accordance with the local codes through the end or top conduit knockout
holes. Make electrical connections to wires inside of “J” box — Black to
black and white to white. Be sure junction box cover inside the unit is
replaced properly. Connect green ground of unit to ground supply wire.
4.
VR600 and VR1000 ONLY
- If VR600 or VR1000
is installed with VCK1 the plug or cap is to remain
over receptacle.
5.
Secure VCK1 into position using four 3/4" long
screws (provided), see figure 1 for mounting
holes.
123
123
123
123
123
123
123
123
123
123
123
123
123
123
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
123
123
12
12
12
12
12
12
12
12
12
12
12
12
➛
➛