Thermador An American Icon PH30ZS Service Manual Download Page 1

Service Manual

for

PROFESSIONAL WALL  HOODS

PH30ZS, PH36ZS, PH42ZS,

PH48ZS, PH54ZS

®

Blower Requirements:  VTN1000Q, VTR600R, VTR1000R, VTR1400Q

Halogen Lamps ......................................................... 1
Infra Red Heat Lamps ............................................. 2
Filters .......................................................................... 3
Step Down Transformer ........................................ 4
Main Relay Board ..................................................... 5
Input Board ............................................................... 6
Heat Sensor .............................................................. 7
Control Panel ........................................................... 8

Cleaning Instructions .............................................. 9
Disassembly ............................................................ 10
Stainless Steel Parts .............................................. 11
Transformer Panel Removal ................................ 12
Input Board Removal ............................................ 13
 Thermador  Hood Warranty .............................. 14
Wiring Diagram ...................... Inside Front Cover

CONTENTS

© 2003 BSH Home Appliances, Corp.

Summary of Contents for An American Icon PH30ZS

















Reviews: