background image

EX-TRAFIRE

®

40SD

Operator Manual, Revision T-15

3-23

Plasma gas supply

The EX-TRAFIRE

®

40SD requires a compressed air supply from a compressor or cylinders, a high 

pressure regulator should be fitted to either form of supply and be capable of delivering gas to the 
filter on the system at a flow rate of 120 l/min at a pressure of 4�5 bar�

Gas type

Air                                     

Nitrogen

Gas quality specification

Recommended Air quality: 

ISO 8573-1 Class 1�2�2�

Air max� particle size: 0�1 microns, 

class 1 ref� to ISO 8573,

Air max� oil: 0�1 mg / m3, 

class 2 ref�: ISO 8573,

Air max� dewpoint: +3° C, 

class 4 ref� to ISO 8573

Purity ≥ 99�99%

Gas quality 

Clean, moisture-free, without oil

Note:

 A poor quality gas supply has a detrimental effect on cut speeds, cut quality, reduced 

thickness of material that can be cut and shorter consumable parts life�

WARNING

Do not allow the input gas pressure to exceed 10 bar/145 psi�  
The filter bowl could explode if the pressure is exceeded�

Note:

 EX-TRAFIRE

®

40SD is equipped with a built-in filtration system�

Additional gas filtration

The Thermacut filtration system should be used when oil, moisture or other contaminants are found 
in the air supply� In more severe cases the 3-stage filtration system should be used�

Gas supply

EX-TRAFIRE

®

40SD

Water / 

particle filter

Oil filter

Oil vapor filter

Summary of Contents for EX-TRAFIRE 40SD









































































Reviews: