4
www.UsePhoenix.com • [email protected]
Toll-Free 1-800-533-7533
4 Service
Servicing the Aquadry TX 80 with its high voltage
circuitry presents a health hazard which could result in
death, serious bodily injury, and/or property damage.
Only qualified service people should service this unit.
Do not operate the unit without all panels in place.
4.1 Technical Description
The Phoenix Aquadry TX 80 uses a high efficiency heat
transfer coil and high volume impeller to transfer and
deliver heat to the structure. The system is designed to
operate with hydronic heating module that use a low-
pressure, open fluid loop distribution system with an
atmospherically vented fluid reservoir. A hydronic heating
module warms the heat transfer fluid. This heated fluid
is pumped through a distribution system loop, passing
through heat exchangers in remote locations. By providing
a clean heat source, the system eliminates the need to
draw in outside air, minimizing energy costs.
4.2 Troubleshooting
Blower not running
1. Unit unplugged, no power to inlet receptacle
2. Power switch not working or thermostat not calling for
heat
3. Wiring fault inside device
4. Defective blower motor or capacitor
Blower running but no heat
1. Airflow restricted at inlet, outlet or fouled coil
2. Heating source not operating
5 Options and Accessories
Accessory Part Description
4029876
DUCTABLE FILTER BOX KIT
4021799
16” x 16” x 2” MERV-8
4028363
16” X 25’ HEAVY DUTY FLEX DUCT
4024936
14” X 250’ LAY FLAT DUCT
6 Wiring Diagram
3.50
3.50
4029457
A
4201 Lien Rd., Madison, WI 53704
1-800-533-7533
BLU
BLK
BLK
BLK
WHT
WHT
WHT
BRN
MOTOR
POWER
SWITCH
LIGHT
MAIN
POWER
SWITCH
T-STAT
ADJ
CAPACITOR
115 VAC, 60 HZ, 1 PH
NOTES:
1. MATL: VINYL FILM PER SES 182
2. CAMERA READY ARTWORK TO BE SUPPLIED BY
TS MARKETING DEPT
3. PROOFS TO BE APPROVED BY TS ENGRG DEPT
4. COLORS: BLACK LINES & LETTERS
ON WHITE BACKGROUND
5. SHEETS WITH SPLIT LINER OR ROLLS
6. MARK PACKAGING CLEARLY WITH DATE OF
MANUFACTURE, TS P/N, REV LETTER & PKG QTY
DWG. NO.
SHEET
REV.
TITLE:
DRAWN BY
CHECKED BY
SIGNATURES / DATE
SCALE
A
1 OF 1
INCHES METRIC [MM]
.X .030 X. 1
.XX .010 X.X 0.5
.XXX .005 X.XX 0.25
ANGULAR TOL. 1
FRACTIONAL TOL. 1/64
1 INCH = 25.4 MM
DIMENSIONS ARE TOLERANCED
AS FOLLOWED:
THIRD ANGLE PROJECTION
MAT'L
Therma-Stor
LLC
P.O. Box 8050, Madison, WI 53708
REL ECO
REV ECO
REV ESA
MCN
DO NOT SCALE DRAWING. DIMENSIONS
AND TOLERANCES PER ANSI Y14.5-1793.
ALL DIMENSIONS ARE BEFORE PLATING.
DEBURR HOLES AND SHARP EDGES .005/.015.
MACHINED SURFACES 125 RMS.
THIS DRAWING IS CONFIDENTIAL AND
PROPRIETARY TO THERMA-STOR LLC. IT IS
LOANED STRICTLY ON CONDITION THAT THE
INFORMATION WILL NOT BE USED FOR THE
BENEFIT OF ANY OTHER ENTITY
4029457
A
SDB
7-15-09
EC
7-15-09
76776
NOTED
1:1
WIRING DIAG,
QUEST DRY HTC
REV APPROVAL
SIZE
