Theben MIX 2 Series Manual Download Page 33

Page: 33 / 50

MIX 2 series RMG 4 U / RME 4 U actuators

5.3.2.11

The "Scenes" parameter page

This page appears when the

Scenes

are activated on the

Configuration options

parameter page.

Each channel can participate in up to 8 scenes.

Table 16

Designation

Values

Description

Block telegram for
scenes

Block with ON telegram

0 = Enable
1 = Block

Block with OFF telegram

0 = Block
1 = Enable

Note:

With this setting the scenes are

always blocked immediately after reset
or download.

All channel scene
statuses

Overwrite on download

A download deletes all scene memories
in a channel, i.e. all previously taught in
scenes.
When a scene number is called, the
channel assumes the configured

Status

after download

(see below).

See appendix: Teach in scenes without
telegrams

Unchanged after download

All previously taught in scenes are
saved.
However, the scene numbers the channel
should react to can be changed (see
below:

Channel reacts to

Participation in central
scene object

yes

Should the device react to the central
scene object?

Channel reacts to

No scene number

Scene number 1

Scene number 63

First of the 8 possible scene numbers the
channel is to react to.

Status after download

Off

New switching status that the selected
scene number is to be allocated to.

Only possible if the scene statuses are to
be overwritten after download.

Permit teach in

Scenes can only be called up.

Yes

The user can both call up and teach in or
amend scenes.

Updated: Apr-15 (Subject to changes) Page 33 of 50

Summary of Contents for MIX 2 Series



















































Search results

Summary of Contents for MIX 2 Series

Reviews:

Related manuals for MIX 2 Series

Brands by name

Popular brands

Theben MIX 2 Series, Manual

Search results

Summary of Contents for MIX 2 Series

Reviews:

Related manuals for MIX 2 Series

Brands by name

Popular brands