Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
Control Throws
19
P.11
C.G
.
20
The ideal C.G. position is 76mm (3
in) behind the leading
edge measured at where the wing meets the fuselage. In order
to obtain the C.G.specified, add weight to the fuselage or move
the battery position. Check the C.G. before flying.
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced
flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by
engine, using
a more powerful engine does not mean better performance. In fact, over powered
engine may cause severe damage an d injuries.
# Make sure the air field is spacious, never fly the plane too close to people and never
get too close to a running propeller.
# If you find wrinkles on the covering as a result of weather changes, you can use hot
iron to remove the wrinkles. Please begin with lower temperature setting and
gradually raise the temperature until the wrinkles are gone. Too hot an iron may
damage the covering .
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
2C
Don't use hot iron near the seams or edges, hot iron will
melt the glue and shrink the covering at the same time, causing the seams to pull away.
0.40-0.46
Warning!
85mm
3.35in
76mm
C.G.
C.G.
3in
S K Y
R A I D E R
M a c h
I I
Elevator
15mm
15mm
Aileron
6mm
6mm
Rudder
20mm
20mm
http://www.theworldmodels.com/para/instruction/instructionManuals.php
A178NPO29981403
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
The W
or
ld Models
Manufacturing Co., Ltd.
w
w
w
.
th
ew
or
ld
m
od
els
.
co
m
