THE WORLD MODELS Katana EP Instruction Manual Download Page 1

Wing Span                          40 in / 1020 mm

Wing Area                           301 sq in / 19.4 sq dm

Flying Weight                    27.5 oz / 780 g

Fuselage Length              35 in / 890 mm

* Specifications are subject to change without notice.*

INSTRUCTION MANUAL

Katana EP

Specifications

Requires : 4-channel radio w/ 4 micro servos,

                  Outrunner Motor KM0283010

                  w/ Propeller Adaptor HW2340100

                  20A brushless ESC, 3 cells 11.1V

                  2100 mAh Li - Po battery & charger. 

                 FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

                                       MADE IN CHINA

Warning! This model is not a toy.

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind

of electric powered precision model.  Operating this model without prior preparation may cause

injuries.  Remember, safety is the most important thing.  Always keep this instruction manual at

hand for quick reference.

The World Models

Manufacturing Co., LTD.

www.theworldmodels.com

Summary of Contents for Katana EP














Reviews: