background image

THE WORLD MODELS

MANUFACTURING CO., LTD.

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

www.theworldmodels.com

Wing Span

Wing Area

Flying Weight

Fuselage Length 

39.5 in / 1000 mm

273 sq in / 17.6 sq dm

24 oz / 680 g

29.0 in / 730 mm

Warning! This model is not a toy.

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind

of engine powered precision model.  Operating this model without prior preparation may cause

injuries.  Remember, safety is the most important thing.  Always keep this instruction manual at

hand for quick reference.

          HIGH

PERFORMANCE

KM0283010

KM0283010

  

Outrunner Motor Included!

      Max Speed 12000 rpm

     Operating Power 180 W

    Operating Voltage 6-12 V

Peak Current 20 A (max 15 s)

      Shaft diameter 3 mm

         Diameter 28 mm

          Lengthe 30 mm

             Weight 60 g

Outrunner Motor

Requires : 4-channel radio w/ 4 micro servos,

                 20A Brushless ESC, 3 cells 11. 1V

                 2100mAh Li - Po battery & charger.

                 Y - harness (1), 6 - inch servo extension (1) 

Specifications

*Specifications are subject to change without notice.*

INSTRUCTION MANUAL

Jeff Troy’s TAMEcat EP ARF

Summary of Contents for Jeff Troy's TAMEcat EP ARF














Reviews: