manualshive.com logo in svg

THE WORLD MODELS Focke-Wulf 190A, Instruction Manual

Share
Download
THE WORLD MODELS Focke-Wulf 190A Instruction Manual Download Page 3

Parts List

P.2

COVERING:--

TOUGHLON STL 322F

TOUGHLON STL 322W

TOUGHLON STL 203 LIGHT GRAY

TOUGHLON STL 331 CUB YELLOW

LIGHTEX SGX 201 BLACK

LIGHTEX SGX 311 FERRARI RED

 1.MAIN WING -- 1 pair
 
 2.RETRACTABLE  LANDING GEAR -- 1 pair
   M2 NUT -- 8 pcs
   SCREW PM2x6mm -- 8 pcs
   WASHER d2xD5mm -- 16 pcs
   MAIN LANDING GEAR COVERS -- 1 pair
   PVC PLATE 0.5mm 20x60mm   -- 2 pcs

3.WING JOINER 6x20x251mm -- 1 pc.

4.PUSHROD Ø1.8x75mm w/ Threads (For Aileron) -- 2 pcs
   SCREW PB2x22mm -- 4 pcs
   SCREW PB2x18mm -- 2 pcs
   SCREW PWA2x8mm -- 8 pcs
   TRI-HORN M3x14mm (S) PL4111221 -- 2 sets
   STRAPER PL4112102 -- 2 pcs 
   CLEVIS PL4112103 -- 2 pcs 
   FUEL TUBE Ø6x5mm -- 4 pcs
   SERVO MOUNTING PANEL PL5310000 -- 1 pair

               DROP TANK -- 1 pc.
               PLYWOOD(A) -- 1 pc.
               PLYWOOD(B) -- 1 pc.
               SCREW PM2x12mm -- 2 pcs
               M2 NUT -- 2 pcs
               WASHER d2xD5mm -- 4 pcs

5.PLASTIC RING PL4112023 -- 2 pcs

   Y-TYPE  PUSHROD Ø1.8x92mm (For Flap) -- 1 pc.
   STRAPER PL4112102 -- 1 pc.
   CLEVIS PL4112103 -- 2 pcs
    FUEL TUBE Ø6x5mm -- 3 pcs
    PLYWOOD 3x38x61mm -- 1 pc.
    LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 2 sets

6.TAIL LANDING GEAR PL7100001 -- 1 set
    FUSELAGE -- 1 pc.
   COLLAR Ø2.1mm w/ set screw -- 1 set
   TAIL WHEEL Ø25mm -- 1 pc.
    SCREW PA3x10mm -- 2 pcs

7.

VERTICAL FIN & RUDDER -- 1 set

8.STABILIZER & ELEVATOR -- 1 set
  
 9.PUSHROD Ø1.8x615mm w/ Threads (For Elevator) -- 2 pcs
    SCREW PB2x16mm -- 6 pcs  
    TRI-HORN M3x14mm (S)  PL4111221 -- 2 sets
    CLEVIS PL4112103 -- 2 pcs 
    FUEL TUBE Ø6x5mm -- 2 pcs

10.PUSHROD Ø1.8x740mm w/ Threads (For Rudder) -- 1 pc.
    SCREW PB2x16mm -- 3 pcs   
    TRI-HORN M3x22mm (S) PL4111301 -- 1 set
    CLEVIS PL4112103 -- 1 pc.
    FUEL TUBE Ø6x5mm -- 1 pc.

11.ENGINE MOUNT PL5111050 -- 1 set

 

    SOCKET HEAD SCREW M4x25mm -- 4 pcs
    WASHER d4xD9mm -- 4 pcs

12.FUEL TANK 380cc PL1111380 -- 1 set
     CABLE TIE 1.5x5x400mm -- 1 pc.
     DOUBLE-SIDE TAPE 40x100mm -- 1 pc.

13.SOCKET HEAD SCREW M3x30mm -- 4 pcs

     M3 NUT -- 8 pcs

    WASHER d3xD7mm -- 8 pcs

    THROTTLE PUSHWIRE Ø1.2x320mm -- 1 pc.
    PLASTIC TUBE d2xD3x230mm -- 1 pc.

14.COWLING --1 pc.
    TRANSPARENT 3D TEMPLATE -- 1 pc.
     SCREW PWA2.6x12mm -- 4 pcs
     SILICON GROMMET d1.5xD6.5mm PL1265035 -- 4 pcs
     SPINNER Ø76mm -- 1 set

15.LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 1 set

16.PUSHROD CONNECTOR PL4410010 -- 1 set
    PUSHROD Ø1.8x65mm (For Elevator) -- 1 pc.
    STRAPER PL4112102 -- 2 pcs  
    FUEL TUBE Ø6x5mm -- 2 pcs

    SPONGE 70x105x60mm -- 1 pc.
     BALSA 5x5x107mm -- 2 pcs

17.SCREW HM4x40mm -- 2 pcs

    WASHER d4.2xD14.5mm -- 2 pcs

18.CANOPY -- 1 pc.
    SCREW PWA2.3x8mm -- 4 pcs
     SILICON GROMMET d1.5xD6.5mm PL1265035 -- 4 pcs
    PILOT PC001050A -- 1 pc.
     WIRE Ø2mm -- 1 pc.

19.DECALS: A322DEC -- 1 set

A322PO27151110

Summary of Contents for Focke-Wulf 190A





















Reviews:

No comments

Brands by name

Popular brands

Load more brands