manualshive.com logo in svg

THE WORLD MODELS Focke-Wulf 190A, Instruction Manual

Share
Download
THE WORLD MODELS Focke-Wulf 190A Instruction Manual Download Page 1

Warning! This model is not a toy.

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind
of engine powered precision model.  Operating this model without prior preparation may cause
injuries.  Remember, safety is the most important thing.  Always keep this instruction manual at
hand for quick reference.      

*Specifications are subject to change without notice.*

INSTRUCTION MANUAL

Wing Span
Wing Area
Flying Weight
Fuselage Length 
 

58.5 in / 1485 mm
539 sq in / 34.8 sq dm
6.5 Ib / 2970 g
49 in / 1250 mm

Specifications

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY(ARF)SERIES

 MADE IN CHINA

The World Models

Manufacturing Co., Ltd.

w w w. t h e w o r l d m o d e l s . c o m

Requires : 0.46-0.55 cu. in. displacement 2-stroke
                   0.70-0.81 cu. in. displacement 4-stroke
                   6-channel radio w/ 6 standard servos
                   and 1 low profile retract servo.

(A322)

A322PO27151110

Summary of Contents for Focke-Wulf 190A





















Reviews:

No comments

Brands by name

Popular brands

Load more brands