THE WORLD MODELS 1/3 Clipped Wing Cub Instruction Manual Download Page 13

Important Safety Precautions

# First time flyer should never fly by himself / herself.  Assistance from experienced flyer is

   absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

   pre-adjusted aircraft.
# 1/3  CLIPPED WING CUB is specially designed to be powered by 80c.c.gasoline engine, 

using a more powerful engine does not mean better performance.  In fact, over powered 

engine may cause severe damage and injuries.
# Make sure  the air field is spacious, never fly the plane too close to people and never get

   too close to a running propeller.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron

   to remove the wrinkles.  Please begin with lower temperature setting and gradually raise

   the temperature until the wrinkles are gone.  Too hot an iron may damage the covering.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary. 

23

Control Throws

Adjust  the control  throws  as shown  in

the diagram. These throws are good  for 

general flying. You can adjust according

to your personal preference.

Aileron

40mm

Elevator

50mm

Rudder

65mm

24

C

.

G

.

The ideal C.G. position is 

150mm(5.9in)

behind the leading edge measured at where 

the  wing meets the  fuselage. In order to obtain the  C.G.specified,add weight to  the

fuselage or  move the  battery  position.  Check  the  C.G. before flying.

A186C0801

65mm

50mm

40mm

150mm

5.9in

Warning!

P.12

Summary of Contents for 1/3 Clipped Wing Cub

















Reviews: