background image

15 mm
15 mm

Ailerons/Elevator

18 mm
18 mm

Rudder

101.6mm

4 in

C.G

.

Important Safety Precautions

Warning!

The ideal C.G. position is 101.6mm(4 in.)behind the leading e

d

ge measured 

at where the wing meets the 

f

uselage.  In order to obtain 

t

he C.G. specified, 

add weight to the fuselage or move the bat

t

ery position.

Check the C.G. before flying.

Adjust the control throws as shown in
the diagram. These throws are good for 
general flying.  You can adjust according
to your personal preference.

# First time flyer should never fly by himself / herself.  Assistance from experienced
   flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly 
   pre-adjusted aircraft.

#

is specially designed to be powered by 

KM0283120 Outrunner Motor.

# Make sure the air field is spacious, never fly the plane too close to people and never
   get too close to a running propeller.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

P.10

Control Throws

10

C.G.

11

(AIR SHOW SCHEME)

http://www.thewingsmaker.com/instructionManuals.php

GM034S1PO28941303

Summary of Contents for GM034S1














Reviews: