8.
9.
INSTALL THE WATER PUMP
1. Attach the water pump in
the indent the tray wall, as
shown in Fig. 5.
2. Place the water pump
power cord in the bottom of
the water tray as shown in
Fig. 5.
Note:The four suction cups
on the water pump should be
attached to the side of the water tray.
INSTALL THE FRAME ASSEMBLY AND TABLE
1. Align the water tray and the frame assembly and table
so that the plug hole in the water tray is on the same
side as the water drain opening in the frame assembly.
2. Place the frame assembly and table into the water tray
(Fig. 6.).
3. Locate the water plug on the frame and insert the water
plug into the drain hole (Fig. 7).
INSTALL THE MOTOR AND ARM ASSEMBLY
1. Place the lower-arm assembly onto the frame assembly
(Fig. 8).
2. Insert the bolts with the spring washers (supplied) into
the lower-arm assembly and thread them into the table
frame. The Lower-arm-assembly hex wrench supplied
can be used to assist in this process.
3. Firmly tighten both bolts (Fig. 9).
Fig. 1
Brake
Fig. 2
Ensure that you have checked the contents in the carton
with the Major Components and Accessories lists before
discarding carton or packing materials.
REPLACEMENT BLADES
We recommend the use of genuine Tile Doctor
replacement blades. Specify Cat. No.: HF180H Blade size:
7” x 5/64” x 5/8” Arbor size: 5/8”
A 7” blade may be used as a replacement.
ASSEMBLY
WARNING! For your own safety and protection, do
not attempt to operate this tile saw until it is completely
assembled and all components and accessories are
properly installed according to this instruction manual.
Read and understand the capability of the tile saw and the
hazards associated with its operation.
WARNING! To avoid injury from unexpected starting
or electrical shock, the tool must remain unplugged
whenever your are performing an assembly, adjustments
or changing accessories.
WARNING! Read all instructions prior to use. Failure to
follow the safety rules listed in this manual and other basic
safety precautions may result in serious personal injury.
SET UP THE STAND
1. Pull one stand leg out of its sleeve, and then pull the
other stand leg out of its sleeve (Fig. 1).
2. Unfold the stand fully and make sure that it is firmly
seated (Fig. 2).
INSTALL THE WATER TRAY
1. Align the water tray on the stand as shown in Fig. 3: the
tray cutout and the stand wheels are on the same side.
2. The water tray will snap into place inside the four pins
on the stand.
3. Make sure that the water tray is securely seated in the
stand (Fig. 4).
Fig. 3
Cutout
Fig. 4
Cutout
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
4. Slide the motor/upper-arm assembly onto the arm-
assembly shaft. The motor must be tilted down towards
the water tray to insure that the motor/upper-arm
assembly can slide fully into place (Fig. 10).
5. Make sure that the motor/upper arm assembly fits snug
with the lower-arm assembly and that you are unable to
see the arm-assembly shaft.
6. Rotate the motor to the vertical position and secure the
motor/upper-arm assembly to the lower-arm assembly
with the depth-adjustment knob (Fig. 11).
7. Fit the lower-arm-assembly cap supplied onto the
lower-arm assembly (Fig. 12).
INSTALL THE WATER HOSE
1. Locate the water hose attached to the motor/upper arm
assembly. Route the water hose from the back of the
blade guard (where it is permanently affixed) to the water
pump, as illustrated by the thick black line in Fig. 13
2. Clips are located on the motor/upper-arm assembly
and lower-arm assembly to secure the water hose (Fig.
14, Fig. 15).
3. Insert the water hose through the hole on the lower-
arm assembly (Fig. 16), and then insert the water hose
into the pump’s intake hole (Fig. 17).
4. Route the pump’s electrical cord through the clip on
the back of the lower-arm assembly and plug it into the
shorter of the two electrical cords attached to the motor
(Fig. 18, Fig. 19).
INSTALL THE BLADE
1. Loosen the wing nut on the blade guard (Fig. 21).
2. Loosen the locking knob on the front inside area of the
blade guard to release the blade guard (Fig. 20).
Fig. 13
Clips for water
hose of pump
Pump
Fig. 12a
Fig. 12b
Fig. 10
Fig. 11
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
