VOL
ECHO
Energy Saving Mode
(Auto Power System-APS)
The unit will automatically switch off after
30 minutes
in the following situations:
1. There is no singing into the microphone;
2. The Bluetooth music has been stopped.
The unit can be switched on again by pressing
POWER
button.
APS is for energy saving purposes.
Troubleshooting Guide
Should this unit exhibit a problem, check the following before seeking service:
No Power
• Power is not on; press the
POWER
button
to turn power on.
• Confirm that the unit is charged.
No Sound – General
• Volume is set to minimum; raise volume of your Bluetooth music device by its
volume control.
No sound from the microphone
• Microphone volume is set to minimum; raise microphone volume by sliding
MIC
button up.
Bluetooth reception failure
• Put the external Bluetooth device close to the unit.
• Pair the unit with the Bluetooth Device as the procedures stated in this manual.
CHARGING THE UNIT
1
Lift the rubber cover on the side of the
unit.
2
Insert the included USB charging cable
into the unit micro USB por
t
u
.
3
Plug the other end of the cable into
computer USB port or other USB
charging device (not included). We
recommend to charge the unit 4 hours
to ensure it is fully charged.
4
T
he speaker will light in red and slowly
flash while the unit is charging. The light
will change to solid red once the unit is
fully charged.
NOTE:
Please charge the unit when you see
the light on the speaker flashing red.
Before you get started
USING A BLUETOOTH DEVICE
3
Once the unit is switched on, you will
hear the Bluetooth sound indicating it is
ready to be paired. The speaker light will
flash in blue. You may also press and
hold the
LIGHT
to initiate the pairing
mode.
Switch on the Bluetooth function of
your Bluetooth compatible device within
three feet of the unit. You will see
“Singing Machine”
appear on your
device’s search list.
Select
“Singing Machine”
to start
pairing. Wait for completion of the
pairing until you hear a beep from the
unit. The speaker light will turn to solid
blue for a while. Please always refer to
the user manual of your Bluetooth
device for detailed instructions.
Note:
If your Bluetooth device prompts you for a passcode during the pairing process,
please enter “0000” to connect. If pairing fails, repeat steps. If you have paired
before, a list of previously searched results will be displayed. Select
“Singing
Machine”
again. On some Bluetooth devices (i.e.,computers), once pairing is
completed, you must select your Bluetooth device as “Use as Audio Device” or
similar.
MUSIC PLAYBACK AND MUSIC VOLUME
Song selection and volume can be controlled from your Bluetooth Device. Adjust the
music volume to a comfortable level.
SING-ALONG MICROPHONE
4
The microphone can be easily located on
top of the unit. You can always sing
through it when the unit has been
switched on.
5
You can adjust the microphone volume by
sliding the
VOL
button on the unit.
6
You can slIde the
ECHO
button to
increase/decrease an echo effect to your
voice.
7
Press and hold the
POWER
button to
turn the unit off; all lights will turn off.
VOL
ECHO
w
V
U
y
VOL
ECHO
u
v
LINE IN CONNECTION
This unit is able to connect your favorite audio device (e.g. iPhone/Tablet/MP3
player,etc.). You can connect your device by using a provided cable
v
(3.5mm
audio cable). LINE IN function is automatically selected once the audio cable is
plugged in.
Warning
- To avoid excessive over amplified sound output, it is recommended that the
volume control is initially adjusted to one third or less and then increase if required.
u
v
Operation
1
Press and hold the
POWER
button
to
turn the unit on; the speaker lights will
start changing gradually.
LIGHT MODE
2
Press the
LIGHT
button repeatedly to
select mode as follows:
Light Mode 1:
The speaker will light up
with changing light colors. When there is
music playback or singing, the lighting will
flash with the audio signal.
Light Mode 2:
The speaker will light up
with color changing lights continuously.
Light Mode 3:
The light will be turned
off.
