background image

 

2013-04-03 

2

*** READ ALL WARNINGS BEFORE OPERATION!*** 

 

Always wear safety glasses when using this log splitter! 

Tie back long hair, roll up sleeves and remove any loose clothing, jewellery or gloves to prevent 

them getting caught in moving parts. 

This log splitter is only intended to be used to split logs!   

Serious injury may occur if this log splitter is used for any other purpose than its intended use. 

 

PLEASE READ PRIOR TO OPERATION: 

 

1. Read and understand this entire instruction manual before using this log splitter. 

2. Always wear safety glasses when using this log splitter to avoid damage to your eyes from 

flying wood pieces. 

3. Never place your hands or other body parts on or near the log, wedge, hydraulic ram, or 

splitter workbench while splitting the log. 

4. Do not use this log splitter for any other purpose other than splitting logs. Do not use this log 

splitter beyond its 8 ton capacity. 

5. Never leave the log or splitter under pressure. 

6. Keep the area around the log splitter clear of any bystanders to prevent injury from ejected 

wood pieces. 

7. Always clear away wood pieces from the log splitter and the area around it before starting on 

another log. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for THMLS













Reviews: