background image

 

 

SPECIFICATION

  

The manufacturer reserves the right to change the product specification and livery according to 
continued product improvements. 

 

Model

 

THET

 

Product Number 

193874002 

Motor 

230v, 50Hz, 800W 

Idle Speed 

400rpm 

Tilling Width 

30cm 

Tilling Depth 

20cm 

Noise Pressure Level (L

PA

73.6dB(A) 

Guaranteed Noise Power Level (L

WA

93.0 dB(A) 

Vibration 

1.131m/s² 

Net Weight 

8.5kg 

 

IMPORTANT INFORMATION 

INTENDED USE 

The product is intended for domestic gardens. This product is not intended for commercial use. 
Generally acknowledged accident prevention regulations and enclosed safety instructions must be 
observed. Only perform work described in these instructions for use, any other use is incorrect. The 
manufacturer will not assume responsibility for damage resulting from such use. 

 

GENERAL SAFETY INSTRUCTIONS 

Read and understand the owner’s manual and labels affixe

d to the product. Learn its application 

and limitations as well as the specific potential hazards. Retain these instructions for future 
reference. The operator is responsible for following the warnings & instructions in this manual and 
on the product. 

 

STAY ALERT  

  

Do not operate the machine while under the influence of drugs, alcohol, or any medication that 
could affect your ability to use it properly. Do not use this machine when you are tired or distracted 
from the job at hand. Be aware of what you are doing at all times. Use common sense. 

AVOID DANGEROUS CONDITIONS  

 

Make sure there is adequate surrounding workspace. Cluttered areas invite injuries. 
Keep your work area clean with sufficient light. Keep the area around the machine clear of 
obstructions, grease, oil, rubbish and other debris which could cause persons to fall onto moving 
parts. 

INSPECT YOUR MACHINE  

  

Check all bolts, nuts, and screws for tightness before each use, especially those securing guards and 
drive mechanisms. Vibration during use, may cause these to loosen. 
Form a habit of checking to see that all other tools/equipment are removed from the working area 
before turning it on. 
Replace damaged, missing or failed parts before using it. Warning labels carry important 
information. Replace any missing or damaged warning labels. 

 
 
 
 

Summary of Contents for THET 193874002





















Reviews: