background image

Page 12

EC DECLARATION OF CONFORMITY

Declaration of Conformity

Pursuant to the regulations of the following EC Directives:

 - Machinery Directive 98/37/EC

 - EMC Directive 89/336/EEC

 - Noise Emissions Directive 2000/14/EC & 2005/88/EC

Handy Distribution Ltd

 hereby decl

a

res that the product:

Machine Type: 

Petrol Chipper Shredder

Machine Model:

 THCS-65

Mass in Kg

: 70kg

Max Cutting Speed:

 2000/min

Engine Speed:

 3600/min

Net Installed Power: 

4.8kW

Conforms to the main safety requirements of the EC Directives listed 

a

bove.

This conformity is based on the following standards and normative documents:

EN 13683:2003

EN ISO 14982:1998

ISO 11094:1991

EN ISO 3744:1995

The conformity assessment procedure followed was in accordance with Annex III of the 

Directive 2000/14/EC.

Measured Sound Power Level:   108.4 dB(A)

Guaranteed Sound Power Level:  110 dB(A)

The responsible person, based within the EC, is identified below

Name:

 Mr Simon Belcher

Title:

 Managing Director

Company: 

Handy Distribution Ltd

Address: 

Hobley Drive, Stratton St Margaret, Swindon, Wiltshire. SN3 4NS

Signature:   

 

 

 

 

Date

:

 15th October 2008

Summary of Contents for THCS-65












Reviews: