background image

Adult assembly required.
CHOKING HAZARD This item contains small parts that have sharp edges and may be a 
choking hazard to children under 3 years old .
Adults should take care when unpacking and assembling this item .
Keep children away during assembly.

IMPORTANT KEEP THIS DOCUMENT FOR 
FUTURE REFERENCE

BEFORE YOU BEGIN ASSEMBLY

PRE-ASSEMBLY

CARE INSTRUCTIONS

Please read all instructions before starting.
It is recommended that 2 people build this bed.
Save all packing materials until assembly is complete to avoid accidentally discarding smaller 
parts and hardware.
Assemble this furniture on a protective surface eg carpet, in the room it will be used. 
Assemble and use on a flat surface.
Please do not use power tools when constructing this piece of furniture .

Wipe clean using a soft damp cloth followed by a dry cloth.
Do NOT use cleaning products which may contain ammonia, solvents or abrasive 
material.
Do NOT expose the furniture to extremes of heat and humidity.

Important: Keep these instructions for further use

If any components are missing or damaged, do not commence assembly and do not use the 
item. Please contact The Childrens Furniture Company  on 0843 289 2646 immediately.

PLEASE READ THE IMPORTANT NOTES ON PAGE 2 

The Jango  Hi Sleeper is supplied in 5 boxes  

1

Jango Hi Sleeper 

(v June 2015)

Summary of Contents for Jango Hi Sleeper











Reviews: