No. Description
Qty.
Item No.
1
Short anchor pin (yellow)
10
7344-W10-C2Y
2
Anchor pin (orange)
10
7061-W10-C1O
3
Joint pin
10
1156-W10-A1R
4
Tube bolt
5
7404-W10-G1O
5
Tube bolt cap
12
7409-W10-F2O
6
Shaft plug
4
7026-W10-H1Y
7
Shaft pin
6
7026-W10-J3R
8
Two-to-one converter
2
7061-W10-G1TB
9
Long button pin
2
7061-W10-E2TY
10
Tube, 30 mm
5
7400-W10-G1D
11
3-hole wide rounded rod
7
7404-W10-C1G2
12
Curved rod (dark green)
5
7061-W10-V1G
13
Curved rod (light green)
5
7061-W10-V1G3
14
5-hole dual rod C
4
7026-W10-S3G1
15
5-hole rod B
4
7413-W10-K2G2
16
7-hole flat rounded rod (light green)
8
7404-W10-C3G2
17
7-hole flat rounded rod (dark green)
4
7404-W10-C3G1
18
7-hole wide rounded rod
1
7404-W10-C2G1
19
9-hole rod
4
7407-W10-C1G
20
Square frame
4
7026-W10-T2G
21
Axle, 35 mm
1
7413-W10-O1D
No. Description
Qty.
Item No.
22
Axle, 60 mm
4
7413-W10-M1D
23
Axle, 70 mm
4
7061-W10-Q1D
24
Small gear
18
7026-W10-D2S
25
Angled arm
3
7404-W10-B2G2
26
Triangular bracket
1
7388-W10-K1G
27
Tube, 200 cm
1
7409-W85-200
28
Anchor pin lever
1
7061-W10-B1Y
29
Tube connector cap
4
7409-W10-F1R
30
3-hole crank (dark green)
4
7409-W10-H1G
31
3-hole crank (light green)
4
7409-W10-H1G1
32
Small cam (pear shape)
2
7409-W10-G1R
33
Large cam (teardrop shape)
2
7409-W10-G2R
34
3-hole 90-degree converter
4
7409-W10-I1G
35
Suction cup pad
4
7409-W85-E
36
Dual valve (light green)
1
7409-W85-D1G1
37
Dual valve (dark green)
1
7409-W85-D1G
38
Pump (light green)
2
7409-W85-C1G1
39
Pump (dark green)
2
7409-W85-C1G
40
Motor box
1
7409-W85-A
41
Geckobot eye stickers
1
R20#7409-US
9 cm x 2
15 cm x 2
17 cm x 2
20 cm x 3
27 cm x 2
NOTE!
Cutting the tube to length
You must cut the 200-cm tube into these lengths. The specific lengths needed for each
model are indicated in the assembly instructions for each model. You will have 4 cm of
tube left over after cutting. You can use the measuring guide on the left edge of this page.
You can also write the lengths on the tubes with a pen so they are easier to tell apart.
16
1
What’s inside your experiment kit:
You will also need:
2 x AAA batteries (1.5-volt, type
AAA/LR03), scissors, ruler or
measuring tape, smooth flat
climbing surface (such as glass,
plastic, or smooth laminate),
small Phillips-head screwdriver,
a few sheets of paper, sheet of
thin plastic (such as a binder
cover), marker
Checklist: Find – Inspect – Check off
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
18
19
20
21
22
23
24
25
26
28
27
29
30
31
32
33
34
35
36
37
38
40
41
39
27
20
17
15
9
Cen
tim
eters
0
› › › KIT CONTENTS
2
GOOD TO KNOW !
If you are missing any
parts, please contact Tham
es & Kosmos
customer service.
US: techsupport@thamesan
dkosmos.com
UK: techsupport@thamesan
dkosmos.co.uk
