TGW CRUZcontrol Installation, Operation & Maintenance Manual Download Page 44

Page: 44 / 62

IOM CRUZcontrol®

P/N: 90480009

Revision Date: 03/18/2019

Page

The following kits are available, which include the photoelectric sensor and appropriate bracket. Even

though not normally needed, an extra reflector and adhesive mounting tape is also included with each

kit.

TGW Systems Part Number

Description

94510097

Photo sensor with bracket, 10-30 VDC NPN output

94510099

Photo sensor with bracket, 10-30 VDC PNP output

94510098

Photo sensor with bracket, 20-264 VAC or 15-30

VDC (NPN) operation

The 10-30 VDC photo sensors are similar to the CRUZcontrol sensors. They are dark switching, with a

50 mA maximum output current, and come with a 6-foot cable (no connector).
The 20-264 VAC / 15-30 VDC photo sensor is an 18 mm barrel type. It is light or dark switching, with a

300 mA maximum output current, and comes with a 6-foot cable (no connector).

Reflectors

Replacement photoelectric reflectors can be ordered with the following part number:

TGW Systems Part Number

Description

400004

Reflector

Sensor Valve Assemblies

A Sensor Valve Assembly is used for applications not requiring accumulation logic, but the solenoid valve

and photoelectric sensor configuration as used in the CRUZcontrol channel is still desired.

TGW Systems Part Number

Description

E0006229

Sick, CRUZ Sen Valve PLC Controlled

Extension Cables

The following extension cables are available to meet application requirements where longer zone lengths

or skipped zones must be accommodated. Each cable has 4 conductors, with male and female M12

connector ends.

TGW Systems Part Number

Description

RK4.4T1RS4.4T

Extension Cable (39 inches)

RK4.4T2RS4.4T

Extension Cable (78 inches)

RK4.4T4RS4.4T

Extension Cable (156 inches)

RK4.4T6RS4.4T

Extension Cable (234 inches)

Summary of Contents for CRUZcontrol































































Search results

Summary of Contents for CRUZcontrol

Reviews:

Related manuals for CRUZcontrol

Brands by name

Popular brands

TGW CRUZcontrol, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for CRUZcontrol

Reviews:

Related manuals for CRUZcontrol

Brands by name

Popular brands