TGW CRUZcontrol Installation, Operation & Maintenance Manual Download Page 43 | Manualshive

Page: 43 / 62

background image

IOM CRUZcontrol®

P/N: 90480009

Revision Date: 03/18/2019

Page

43

of

58

NBA

®

23 Brake Control

When a discharge zone brake assembly is provided with NBA 23 conveyor, the brake control comes

already wired and plumbed from the factory. The following is provided to explain how it functions.

The two photoelectric sensors as shown are located in the discharge zone, sharing the same hole through

the conveyor side channel and aimed at the same reflector. In this way they will always simultaneously

sense the presence or lack of product. The Brake Logic Assembly is progressive logic, which passes

the run or accumulate status upstream to the next logic assembly, which in this situation is the same

zone. The Brake Logic Assembly is also XenoROL

®

, since an accumulated condition requires air to

activate the brake.

Auxiliary Photoelectric Sensors

There is often a need to sense product presence on a CRUZcontrol equipped conveyor, with the sensors

connected to a control system other than CRUZcontrol. To allow for this, adequate space has been

provided along side of the CRUZcontrol photoelectric sensors to allow for the mounting of a second

independent photoelectric sensor, sharing the same holes through the conveyor side channels and the

same reflector. Appropriate holes are provided for the photoelectric sensor mounting bracket. The

discharge end of NBA 23 conveyor is also provided with an additional mounting location for a

photoelectric sensor and reflector (straight across scanning, no offset).

CONVEYOR FLOW

BRAKE LOGIC ASSEMBLY

PROGRESSIVE LOGIC

XENOROL E0001904A

NBA 23 LOGIC ASSEMBLY

BASIC OR PROGRESSIVE

BRAKE SENSOR

ZONE SENSOR

«
...
41
42
43
44
45
...
»

Summary of Contents for CRUZcontrol































































Reviews:

No comments

Related manuals for CRUZcontrol

Brand: Lakeshore Pages: 192

Brand: QUAD Pages: 16

Brand: CALEFFI Pages: 2

Brand: CALEFFI Pages: 12

Brand: Caliber Pages: 6

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

ECL Comfort 300

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 8

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 12

ECL Comfort 110

Brand: Danfoss Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands