background image

©Copyright Task Force Tips  LLC  2020 

LIM-032 February 18, 2020 Rev00

8

6.0  FLOW CHARACTERISTICS
6.1  MASTERSTREAM 4000 ER AUTOMATIC

Within its 

fl

 ow range, the Masterstream 4000 ER automatic nozzle operates at the nominal pressure of 80-120 psi (5.5-8.3 bar, 550- 

830 kPa). The following chart shows the typical performance of this nozzle.

0

20

40

60

80

100

120

140

160

0

1000

2000

3000

4000

5000

6000

FLOW (gpm)

P

R

ESSU

RE (psi

)

0

2

4

6

8

10

0

4000

8000

12000

16000

20000 FLOW (l/min)

PRES

SURE (bar

kPa

/1

00)

FLOW RANGE

110 psi  SETTING

100 psi SETTING

90 psi  SETTING

80 psi SETTING

120 psi  SETTING

MASTERSTREAM 4000 ER AUTOMATIC

8 bar

7 bar

6 bar

Figure 6.1

6.2  MASTERSTREAM 4000 ER SELECTABLE

The Masterstream 4000 ER Selectable nozzle allows the user to select one of several ori

fi

 ce sizes to achieve desired 

fl

 ows at the 

rated pressure of the nozzle. The following chart gives relationship of 

fl

 ow and pressure for the various ori

fi

 ce sizes.

0

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

11000

12000

13000

14000

15000

0

2

4

6

8

10

12

0

20

40

60

80

100

120

140

160

180

200

0

500

1000

1500

2000

2500

3000

3500

4000

Flow (l/min)

No

zzl

e

 P

re

ssu

re

 (b

ar

)

No

zzl

e

 P

re

ssu

re

 (p

si

)

Flow (gpm)

MASTERSTREAM 4000 ER SELECTABLE

4000 gpm

(15000 l/min)

Se

ƫ

ng

3000 gpm

(11000 l/min)

Se

ƫ

ng

2000 gpm

(7500 l/min)

Se

ƫ

ng

Figure 6.2

Summary of Contents for Masterstream 4000 ER AUTOMATIC

















Reviews: