Textron Ransomes 933303H Operator'S Manual Download Page 27

EC Declaration of Conformity

     

The Undersigned Manufacturer:

 

Schiller Grounds Care, Inc.

 

One Bob-Cat Lane

 

Johnson Creek, WI 53038

EU Authorized Representative:

 

Earlsmere Limited

 

Unit 18 Valley Road 

 

Station Road Industrial Estate

 

Wombwell, Barnsley, South Yorkshire, S73 OBS UK

Notified  Body: 

                                                                                                           

 

AV Technology Ltd

 

AVTECH House, Arkle Avenue

 

Stanley Green Trading Estate

 

Handforth, Cheshire, SK9 3RW UK

Declare that the machine described below:

 

Make & Type: ..................................................

BobCat, Hydro Midsize

 

Category: ........................................................

Lawnmower, Walkbehind, Rear Discharge

 

Series: ............................................................

933303H

 

Engine: ...........................................................Kawasaki, 

FS

541V-AS52

 

Speed: ............................................................

2850 R.P.M

 

Net Installed Power ........................................

13.4 KW (18HP)

 

Operation Width: ............................................

914mm (36”)

Declare that the machine described below:

 

Make & Type: ..................................................

BobCat, Hydro Midsize

 

Category: ........................................................

Lawnmower, Walkbehind, Side Discharge

 

Series: ............................................................

933304H

 

Engine: ...........................................................Kawasaki, 

FS541V-AS52

 

Speed: ............................................................

2850 R.P.M

 

Net Installed Power ........................................

13.4 KW (18HP)

 

Operation Width: ............................................

914mm (36”)

Complies with the provisions of the following European Directives and Amendments and the Regulations transposing it into 

national law:

 

Machinery Directive ..................................................................

2006/42/EC

 

EMC Directive ..........................................................................

2004/108/EC

 

Noise in the Environment Directive ..........................................

2000/14/EC - Annex VI Procedure 2

 

Vibration Directive ....................................................................

2002/44EC

 

Non Road Emissions ................................................................

2002/88/EC

 

Pedestrian Controlled lawnmowers ..........................................

EN836

Sound:  

Sound levels were determined in accordance with Directive 2000/14/EC and standards EN13684

              and ISO 11094.

              Measured Sound power level: .............................Model 933303H & 933304H……  

98 dB

              Guaranteed Sound power level: ..........................Model 933303H & 933304H……..

99 dB

 

                                           Operator Ear: ..........................Model 933303H & 933304H……..

84 dB 

Vibration:

Hand/arm vibration was measured at the right and left operator handles per ISO 5349-1-2001 and ISO 5349-2-2001.  

Vibration is given as the vector sum of acceleration in the x, y and z axes.  Only the highest of the left and right read-

ings is given.

Guaranteed Vibration level …………4.64 m/s2

Intended Use and Limits:

This machine is for use cutting grass on normally maintained grass covered areas as a walk-behind lawnmower.  Loss 

of control may result on steep slopes.  Before operating on a slope, evaluate the risks involved.

4166801 REV B

Kurt Knudsen

Director of Operations

Date:  6th  January, 2014

Jim White

Managing Director

Date:  6th  January, 2014

Summary of Contents for Ransomes 933303H





























Reviews: