Textron Jacobsen HR-5111 Technical/Repair Manual Download Page 142

Page: 142 / 423

4-92

4203780 First Edition

ELECTRICAL

Horn/Test Switch

Removal and Installation

See Figures 4-73 and 4-74.

Park the mower safely. (See “Park Mower Safely” on
page 1-6.)

Disconnect the battery negative (–) cable at the
battery.

Remove instrument panel. (See “Instrument Panel”
on page 4-110.)

Figure 4-73

Figure 4-74

Remove bezel nut (1).

NOTE

Label all wires before disconnecting to ensure correct
installation.

Disconnect wire terminals (2).

Remove horn/test switch (3).

Installation Notes

• Adjust jam nut (4) for proper switch height if

necessary.

• Install horn switch by reversing the order of removal.

Seat Switch

Removal and Installation

See Figures 4-75 through 4-77.

Park the mower safely. (See “Park Mower Safely” on
page 1-6.)

Disconnect the negative (–) battery cable at the
battery.

Figure 4-75

Tilt seat back (1) to forward position.

Cut cable ties (5).

NOTE

Label all wires before disconnecting to ensure correct
installation.

Disconnect wire connector (6).

Remove two screws (3).

Disengage lower seat back tabs (4) from seat back
support (2).

Push bottom of seat back (1) forward; lift and remove
seat back.

Lift rear of seat (7); slide forward and remove seat.

TN1936

TN1937

TN1987

Summary of Contents for Jacobsen HR-5111








































































































































































































































































































































































































































Search results

Summary of Contents for Jacobsen HR-5111

Reviews:

Related manuals for Jacobsen HR-5111

Brands by name

Popular brands

Textron Jacobsen HR-5111, Technical/Repair Manual

Search results

Summary of Contents for Jacobsen HR-5111

Reviews:

Related manuals for Jacobsen HR-5111

Brands by name

Popular brands