background image

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

EK1550LT and EK1550LX Battery-powered Crimping Tools

Description

The EK1550LT and EK1550LX Battery-powered, High-

speed Crimping Tools are hand-held, self-contained 

crimping tools intended to crimp aluminum and copper 

connectors onto electrical cable.
These tools have a retraction stop feature which allows 

the operator to stop the retraction motion of the ram to 

shorten cycle time.
Both the T and X versions of this tool have Bluetooth

®

 

connectivity and an LCD screen. Only the T version has 

GPS tracking.
These tools are protected by U.S. Patent No. 6,206,663, 

6,276,186, 6,401,515, and 6,718,870.

EK1550LT—FCC ID: 2AGL2COM; IC ID: 20646COM 

EK1550LX—FCC ID: 2AGL2CFM; IC ID: 20646CFM

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and 

(2) this device must accept any interference received, 

including interference that may cause undesired 

operation.

Safety

Safety is essential in the use and maintenance of  

Greenlee tools and equipment. This manual and any 

markings on the tool provide information for avoiding 

hazards and unsafe practices related to the use of this 

tool. Observe all of the safety information  provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with  

the safe operation and maintenance procedures for the 

following Greenlee tools:
•  EK1550LT Battery-powered Crimping Tool
•  EK1550LX Battery-powered Crimping Tool
Keep this manual available to all personnel.
Replacement manuals are available upon request at  

no charge at www.greenlee.com.

Do not discard this product or throw away!

  

For recycling information, go to www.greenlee.com.

All specifications are nominal and may change as design 

improvements occur. Greenlee Textron Inc. shall not be liable for 

damages resulting from misapplication or misuse of its products.
GATOR is a registered trademark of Textron Innovations Inc.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Blackburn is a registered trademark of Thomas & Betts.

KEEP THIS MANUAL

Table of Contents

Description ..................................................................... 2
Safety ............................................................................. 2
Purpose of this Manual .................................................. 2
Important Safety Information ..................................... 3–4
Identification ................................................................... 5
Specifications ................................................................. 5
Adapter Kits ................................................................ 6–8
Setup .............................................................................. 8
Operation .................................................................. 9–10
Die Selection ................................................................ 11
Connector Selection ..................................................... 11
LCD Screen .................................................................. 12
Maintenance ................................................................. 13
Troubleshooting ............................................................ 14

Summary of Contents for Greenlee EK1550LT

















Reviews: