manualshive.com logo in svg

Texmo Industries Taro Pumps NCH 2250, Instructions & Operating Manual, Page: 21 / 34

Share
Download
Texmo Industries Taro Pumps NCH 2250 Instructions & Operating Manual Download Page 21

Connecting the Power Supply

Caution

Observe relevant Electricity Board regulations while powering up the pumpset

Warning

 Before inserting the power plug or connecting the wires to the terminal board, make 
sure the power supply is properly disconnected. Failure to do so may lead to electrical 
shock, short, or injury caused by the unintended starting of the pump

Caution

Do not use damaged cables, power plugs, or loose power outlets. Failure to observe 
this precaution could lead to electrical shock, short circuit or fire

Power cable connection to Non-clog Sewage Pump

Refer Fig. 9a and 9b, shown below, for connecting the lead wires to the Terminal Board of Single-phase and Three-
phase Non-clog Sewage Pumps.

Connection diagram for capacitor start and run motor

Note: If top fails, interconnect Z2 & A2 using 1.5 mm² wire

Z1

Z2

A1

A2

CONNECT 220V SINGLE PHASE

SUPPLY TO A1 & A2

(GREEN)

CAPACITOR

TOP

STARTING COIL

(RED)

(YELLOW)

RUNNING COIL

(BLUE)

Z1

Z2

A1

A2

Fig. 9 Cable lead wire connections

Fig. 9(a) Single-phase - NMH-S 7040 / NMH-S1550

OMSP001A

21

2020.01

Summary of Contents for Taro Pumps NCH 2250



































Reviews:

No comments