Shredder Capacity:
The CD1412 will shred 12 sheets of A4 70g paper at once or 1 Credit Card or 1 x DVD/CD,
and will accept paper width up to 220mm.When shredding smaller items like envelopes or
credit card receipts/Credit Cards, insert them through the middle of the feed slot.
The paper sensor is located in the centre of the main feed slot. When paper is inserted, the
sensor starts the cutters. When the paper has gone through the shredder, the sensor will
switch the cutters off.
Operating the Shredder
:
1. Prepare the paper to be shredded by removing paper clips, and any other objects that
may jam in the feed slot. The Shredder will shred staples, though for optimal
performance, their removal is advised
2. Only feed 12 sheets of 70g A4 paper at any one time or 1 Credit Card or 1 DVD/CD
PLEASE NOTE
– There are two power switches/buttons on this Shredder, one at the back
of the Shredder, the other at the front.
Switches located at the back of the Shredder
O
: Power on when pressed down
-
: Power off when pressed down
Buttons located at the front of the Shredder
REVERSE
: Reverses the shredding direction and backs items out of the shredder in the
event of a paper jam, can also be used in conjunction with the Forward button, to clear paper
jams.
POWER
: Press once to switch the power on, indicated by the Red ready light, press again
and the power is switched off. For this button to work the Rocker switch located at the back
of the shredder, must have the O switch pressed down.
FORWARD
: Allows the cutters/blades to shred in a forward direction without paper being
inserted, normally used in conjunction with the reverse switch to clear any paper jams.
Waste Bin:
This Shredder has a pull out waste bin for mess free emptying. It is also fitted with a Safety
Switch that cuts off the power when the waste bin is removed. To switch it back on when the
bin is placed back into the Shredder, press the power button at the front of the Shredder.
PLEASE NOTE
– If the waste bin is not placed back correctly, the Shredder will not work.
The Shredder is on castor for easy movability
Paper Jams:
The CC1610 is equipped with a motor overload/overheat protection device and the power
may terminate automatically in case of the following situations:
1. Operating the shredder at maximum capacity continuously for a prolonged period of
time, e.g. more than 2 minutes duty cycle without stopping.
2. Exceeding the shredding capacity e.g. inserting more than 12 sheets at one time, or if
the paper is not fed squarely into the feed slot.
Both of these operations may result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs, you should either:
1 . Press the reverse button and remove any excess paper, now press the forward button,
this should then clear the paper jam. If the paper is still jammed in the blades then
alternately press the forward and reverse buttons 2-3 times, the paper jam should now
be cleared.
OR
2 If the Shredder does not work then you need to unplug the power cord from the AC
outlet and wait at least 30 minutes for the overload protection to reset.
3 After 30 mins, plug the power cord back into the AC outlet and press the power button,
so the red ready light comes on. Any paper still in the shredder should automatically be
shredded, if not follow the above instructions in point 1.
Clearing the Blades of Paper Jams
If paper becomes jammed during shredding, press the reverse button and remove any
excess paper from the feed slot, press the forward button, this should clear the paper jam.. If
paper is still jammed then press the forward and reverse buttons alternately, 2-3 times,
which should then finally clear the paper jam.
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.
DO NOT, UNDER ANY CIRCUMSTANCES, INSERT METAL OBJECTS INTO THE ENTRY
FEED SLOT OR THE BLADES, TO REMOVE THE JAMMED PAPER.
Maintenance
Warning
:
When you want to maintain the shredder, please make sure you have switched off the
shredder and removed the plug from its socket.
Use a damp/dry soft cloth when you want to clean the shredder.
The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinners to avoid fading or scratches.
Do not allow water to enter the shredder head when cleaning.
To maintain the quality of your shredder blades please use Texet LB12 lubricating
sheets once a month, these can be bought from our ebay store – Texet Sales Ltd.
