Texas Razor 5110 TR/W, Instruction Manual

Page: 13 / 15

13
Water nozzle
The left side of the mower deck is fitted with a water
nozzle for washing the deck. (See Illustration ID-J)
● Attach a hose to the nozzle.
● Turn on the water and start the engine.
● The rotations of the blades, will ensure that the
water will clean the underside of the deck.
Note:
For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.
Oil change
Oil should be changed for the first time after 2 hours,
then at least 1 time per year. An efficient oil change
is best done by hot engine. Use an oil suction kit.
Oil and Oil suction kit not included.
1. Suck the oil through the oil filler hole with the
cyringe. Use the hose to reach the bottom of the
engine.
2. Tap the used oil into the supplied bottle.
3. Refill oil on the engine type SAE30 (0,6 litre).
Keep the empty oil bottle for next time.
4. Use the dipstick on the oil plug to check the oil
level.
Dispose of the used oil, eco-friendly. Use your local
recycling center.
Air Filter
The air filter should be inspected and cleaned
regularly. If the filter has not been cleaned for a long
time, the engine’s power will drop.
See Illustration A2
1. Clean around the air filter before removing it.
2. Push the two flaps down and gently pull the
cover
3. Carefully remove the paper filter and inspect
it. Brush it with a soft brush. If it is very dirty,
replace it. Be careful that no dirt gets into the
inlet.
4. Wash the black foam element in the right side in
warm water and soap.
5. Press the water out of the foam element and let
it dry. Put a few drops of SAE-30 oil on the filter
to moisten it lightly. Carefully squeeze out any
surplus oil.Remount the element.
6. Please note that all parts are assembled
correctly and properly closed, as shown in the
picture.
Cable Adjustment
The following cables may be necessary to
readjust: Illustration A1
1. Cable for self-propelled (clutch cable)
2. Cable for engine brake
Note: The throttle cable can not be adjusted!
Adjusting the clutch cable: Illustration A1-1
If you experience slack in the clutch cable, this can
be solved simply by tighten or loosen the bolt.
1. Tighten turning clockwise - loosen the cable.
2. Tighten turning anti clockwise - tigthen the cable.
Adjusting the brake cable: Illustration A1-2
If you experience slack in engine brake cable, this
can be solved simply by tighten or loosen the bolt.
Operation
Always check and refill oil before the start!
The oil level should always be between min. and
max. on the dipstick. Fill with SAE-30 oil. There
should be a total 0.6 liter oil in the engine. Use only
unleaded 95 octane fuel to the engine. Never overfill
the tank.
Cutting height adjustment: Illustration F1
The mower has 6 different heights. The cutting
length of the grass ranges from 25 mm to 76 mm
Start: Illustration F2
1. Set the choke lever on full ”choke”
(only by cold engine)
2. Move the throttle lever to full (hare)
3. Pull the engine brake bar and hold to release the
starter cord on the engine.
4. Pull starter cord, in one quick stroke, to start.
Important: Always slide the start-cord back
5. Immediately after the engine has started, return
the choke lever in the ”run” postion.
6. Adjust the throttle lever if necessary
7. Activate the bar for self-propelled in order to start
mowing.
Note: As long as operating the mower, the bar for
engine brake must be engaged.
Stop: Illustration F2
1. Release the engine brake and self-propelled bar
to turn off the mower and the engine
Note: The blades will still rotate at up to
3 seconds after stopping.