Texas Razor 4600 Li, User Manual

Page: 14 / 21

14
Mounting
Unpacking: Illustration 2
Remove the mower from the box by pulling the machine
out form the side. The box contains:
1 pcs mower
4 pcs wing nut set consisting of wing nuts, bolts
and washers.
2 pcs spacer blocks (See illustration 6-1)
1 pcs. battery
1 pcs. charger
Warning: Ensure that cables are not pinched.
Handlebar and height adjustment: Illustration 3+4
The handlebars are height adjustable. This means that
they can be adjusted so that it best fits you. Before you
install the handlebar, it may be a good idea to have
decided which height is best for you.
1. Set the lower handlebar tube to the working height
that suits you. “H” is high position and the “L” is low
position.
2. Attach the wing nut from the inside of the side
bracket and into the lower handlebar.
3. Attach the upper handlebar on the lower. Fasten
with wing nut from the inside of the handlebar.
4. Customize cable and secure with cable clamps
Mounting the grass collector: Illustration 5
1. Click the frame to the grass collector.
The grass collector comes with a handy indicator
showing whether the box is full of grass and needs
emptying.
Rear discharge guard: Illustration 6-1
If you want to mow without grass collector it is important
to attach the two spacer blocks.
1. Insert the 2 blocks (ID:E) under the rear discharge
guard.
Note: The spacer blocks are for rear ejection only!
Otherwise they should be removed.
Warning: If the two blocks are not mounted. The
mower will have difficulties to dispose the grass.
Mulching plug: Illustration 6-2
1. Insert the mulching plug and remove side
discharge guard, if you want to mow with mulching
functionality.
NB Don’t use the grass collector
Important: Remember to remove the mulching plug,
when using the grass collector.
Side discharge guard: Illustration 6-3
1. Press the lock button and lift the side guard up and
insert side discharge guard. Then insert the
mulching plug in rear discharger to mow with side
discharge function. NB Don’t use the grass
collector.
Battery
Warning:
Do not try to dissassemble, short circuit or
put it to extreme heat or fire, as it can cause serious
inquiry and permanent damage to the battery!
Charging
Only use the original charger with art. no.
90066677.
Before the battery is being used the first time, it is
recommende to full charge it first.
The battery has an energy indicator. Press the button
and a number of LED lighs will flash (Illustration 7):
•
4 lights: 100% battery power
•
3 lights: 75% battery power
•
2 lights: 50% battery power
•
1 lights: Less than 25% battery power
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important
To protect the battery from total discharge, the
machine will stop, when the battery is nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
Waste lithium batteries must not be disposed
of with the household waste. Batteries
should be taken to your local recycling
centre for safe treatment.
Charging
Only use the original charger, which is included
with the product and do not try to charge other type
of batteries in the charger, other than the original
battery with art. no. 90066676.
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It should
be connected to a normal 230V AC socket.
Before the battery is being used the first time, it is
recommended to charge it fully.
The surface of the battery can become warm
during charging. This is normal.
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it lockes.
There are 4 lights on the charger indicating the status
and state of charge of the battery (Illustration 8):
•
Constant red light
: The charger is ready to
charge, but no battery is connected
•
Flashing red light
: Battery fault or overheat
(always let a warm battery cool off before
charging it)
•
Flashing green light
: Battery is charging
•
Constant green light
: Batteri er fuldt oplades og
skal fjernes fra opladeren.
The charger will stop, when the battery is full.
However, it is not recommende to leave the battery in
charger for more than 24 hours.