Texas Instruments TUSB1142 User Manual Download Page 7 | Manualshive

Page: 7 / 11

Texas Instruments TUSB1142 User Manual Download Page 7

3 Quick Start Guide

The following instructions assume the EVM is configured for pin-strap mode and is powered from the VBUS.
1. Insert Micro-B USB cable into the Micro-B receptacle (J1) and connect the Type-A receptacle of the

motherboard to the EVM through the same cable.

2. Insert a USB-C cable or USB device into the USB-C receptable side of the EVM.
3. The USB device should enumerate. If USB device does not enumerate, check to ensure the FLIP pin (JMP4)

is set based on the CC pin orientation.

The instructions below assume the EVM is configured for I2C mode and is powered from the barrel jack.
1. Ins5 V DC Power source into barrel jack (J1).
2. Configure TUSB1142 through the I2C interface, JMP4, and JMP5.
3. Insert the Micro-B USB cable into the Micro-B receptacle (J1) and connect the Type-A receptacle of the

motherboard to the EVM through the same cable.

Note

For I2C operation, ensure that R19 is populated.

4. Insert a USB-C cable or USB device into the USB-C receptable side of the EVM.
5. The USB device should enumerate. If the USB device does not enumerate, check to ensure the FLIP pin

(JMP4) is set based on the CC pin orientation.

Quick Start Guide

SLLU350 – APRIL 2022

Submit Document Feedback

TUSB1142 EVM User's Guide

7

Copyright © 2022 Texas Instruments Incorporated

«
...
5
6
7
8
9
...
»

Summary of Contents for TUSB1142












Reviews:

No comments