manualshive.com logo in svg

Texas Instruments TSW14J58 JESD204C, User Manual, Page: 13 / 23

Share
Download
Texas Instruments TSW14J58 JESD204C User Manual Download Page 13

8. With J35 = 1–2, open up the new “xx.mcs” file to be loaded, and check the following setup in the

programming. Click the 

OK

 button when completed. 

Figure 3-3

 illustrates the configuration file to be loaded.

Figure 3-3. Config file

9. Press SW4 to reload the EEPROM
10.Press SW3 to reset FPGA
11.With J35 = 2–3, open up the new “yy.mcs”file to be loaded and check the following setup in the programming.

Click the 

OK

 button when completed.

3.3.3.4 USB I/O Connection

Control of the TSW14J58EVM is through the USB 3.0 connector J1 and USB 2.0 connector J23. This provides
the interface between the HSDC Pro GUI running on a PC using the Microsoft

®

 Windows

®

 operating system

and the FPGA. For the computer, the drivers needed to access the USB port are included on the HSDC Pro
GUI installation software that can be downloaded from the web. The drivers are automatically installed during the
installation process. On the TSW14J58EVM, the USB port is used to identify the type and serial number of the
EVM under test, load the desired FPGA configuration file, capture data from ADC EVMs, and send test pattern
data to the DAC EVMs.

www.ti.com

Hardware Configuration

SLWU094 – MARCH 2021

Submit Document Feedback

TSW14J58 JESD204C Data Capture and

Pattern Generator Card

13

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TSW14J58 JESD204C
























Reviews:

No comments