background image

List of Figures

Figure 1-1. TPS7A13EVM-057 Evaluation Module.....................................................................................................................

1

Figure 3-1. TPS7A13EVM-057 Turn On......................................................................................................................................

5

Figure 3-2. TPS7A13EVM-057 With Current Probes Attached...................................................................................................

6

Figure 3-3. TPS7A13EVM-057 Load Transient Results: 1-mA to 300-mA Load Step.................................................................

7

Figure 3-4. TPS7A13EVM-057 Load Transient Results: 300-mA to 1-mA Load Step.................................................................

8

Figure 4-1. Top Assembly Layer and Silk Screen........................................................................................................................

9

Figure 4-2. Top Layer Routing.....................................................................................................................................................

9

Figure 4-3. Layer 2......................................................................................................................................................................

9

Figure 4-4. Layer 3......................................................................................................................................................................

9

Figure 4-5. Bottom Layer Routing..............................................................................................................................................

10

Figure 4-6. Bottom Assembly Layer and Silk Screen................................................................................................................

10

Figure 5-1. Schematic................................................................................................................................................................

11

1 Trademarks

LeCroy

 is a trademark of Teledyne LeCroy.

Kapton

®

 is a registered trademark of DuPont.

All trademarks are the property of their respective owners.

Trademarks

www.ti.com

2

TPS7A13EVM-057 Evaluation Module

SBVU074 – NOVEMBER 2021

Submit Document Feedback

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TPS7A13EVM-057




















Reviews: