Texas Instruments TPS65300-Q1 User Manual Download Page 1

User's Guide

SLVU685 – February 2012

TPS65300EVM

Contents

1

Introduction

..................................................................................................................

2

2

Setup

.........................................................................................................................

2

2.1

Input/Output Connector Description

.............................................................................

2

2.2

Setup

................................................................................................................

6

2.3

Operation

............................................................................................................

6

3

Board Layout

................................................................................................................

7

4

Schematic and Bill of Materials

...........................................................................................

9

4.1

Schematic

...........................................................................................................

9

4.2

Bill of Materials

....................................................................................................

10

List of Figures

1

EVM Board

...................................................................................................................

2

2

IGN Jumper Settings

.......................................................................................................

3

3

EN Jumper Settings

........................................................................................................

3

4

3.3V PWR Jumper Settings

...............................................................................................

4

5

1.2V PWR Jumper Settings

...............................................................................................

4

6

Bridge Jumper Settings

....................................................................................................

4

7

Top Assembly Layer

........................................................................................................

7

8

Top Layer Routing

..........................................................................................................

8

9

Bottom Layer Routing

......................................................................................................

8

10

TPS653000EVM Schematic

...............................................................................................

9

List of Tables

1

Device and Package Configurations

.....................................................................................

2

2

TPS65300EVM Bill of Materials

.........................................................................................

10

PowerPAD is a trademark of Texas Instruments.

1

SLVU685 – February 2012

TPS65300EVM

Submit Documentation Feedback

Copyright © 2012, Texas Instruments Incorporated

Summary of Contents for TPS65300-Q1




















Reviews: