background image

User’s Guide

TPS65265 Buck Converter Evaluation Module User's
Guide

ABSTRACT

This document presents the information required to operate the TPS65265 PMIC as well as the support
documentation including schematic, printed-circuit board (PCB) layout, hardware setup, and bill of materials.

Table of Contents

1 Background

.............................................................................................................................................................................

2

2 Schematic

................................................................................................................................................................................

3

3 Board Layout

...........................................................................................................................................................................

4

4 Bench Test Setup Conditions

................................................................................................................................................

7

4.1 Header Description and Jumper Placement......................................................................................................................

7

5 Power-Up Procedure

..............................................................................................................................................................

9

6 Bill of Materials

.....................................................................................................................................................................

10

7 Revision History

...................................................................................................................................................................

10

Trademarks

All trademarks are the property of their respective owners.

www.ti.com

Table of Contents

SLVUAK9A – DECEMBER 2015 – REVISED MAY 2021

Submit Document Feedback

TPS65265 Buck Converter Evaluation Module User's Guide

1

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TPS65265

















Reviews: