background image

User's Guide

SLVU202B – May 2007 – Revised November 2007

TPS61050EVM-215 and TPS61052EVM-215

This user’s guide describes the characteristics, operation, and use of the TPS61050EVM-215 and
TPS61052EVM-215 evaluation modules (EVMs). This EVM demonstrates either the Texas Instruments
TPS61050 or TPS61052 synchronous boost converter based high power WLED driver with I

2

C interface.

This document includes setup instructions, a schematic diagram, a bill of materials, and PCB layout
drawings for the evaluation module.

Contents

1

Introduction

...................................................................................................................

2

2

Setup

..........................................................................................................................

2

3

Software Setup and Operation

.............................................................................................

6

4

Test Results

..................................................................................................................

7

5

Board Layout

................................................................................................................

11

6

Schematics and Bill of Materials

.........................................................................................

14

List of Figures

1

TPS6105x Software Main Panel

...........................................................................................

6

2

LED Efficiency vs. Input Voltage - Torch Mode

..........................................................................

7

3

LED Efficiency vs. Input voltage - Single Pulse Flash Mode

...........................................................

8

4

Torch Flash Sequence

......................................................................................................

8

5

Start Up in Torch

.............................................................................................................

9

6

Inrush Current at Flash

....................................................................................................

10

7

Voltage Mode Efficiency

...................................................................................................

10

8

Voltage Mode Load Transient

............................................................................................

11

9

Assembly Layer

.............................................................................................................

12

10

Top Layer

....................................................................................................................

12

11

Layer 2

.......................................................................................................................

13

12

Layer 3

......................................................................................................................

13

13

Bottom Layer

................................................................................................................

14

14

TPS61050/2EVM-215 Schematic

........................................................................................

15

List of Tables

1

Jumper Settings

..............................................................................................................

5

2

HPA215 Bill of Materials

...................................................................................................

16

Windows is a trademark of Microsoft Corporation.
I

2

C is a trademark of Philips Corporation.

VeriSign is a trademark of VeriSign, Inc..

SLVU202B – May 2007 – Revised November 2007

TPS61050EVM-215 and TPS61052EVM-215

1

Submit Documentation Feedback

Summary of Contents for TPS61050EVM-215



















Reviews: