background image

User’s Guide

TPS53515 Step-Down Converter Evaluation Module User's 
Guide

Table of Contents

1 Introduction

.............................................................................................................................................................................

2

2 Description

..............................................................................................................................................................................

2

2.1 Typical Applications............................................................................................................................................................

2

2.2 Features.............................................................................................................................................................................

2

3 Electrical Performance Specifications

.................................................................................................................................

2

4 Schematic

................................................................................................................................................................................

3

5 Test Setup

................................................................................................................................................................................

4

5.1 Test Equipment..................................................................................................................................................................

4

5.2 Recommended Test Setup.................................................................................................................................................

5

6 Configurations

........................................................................................................................................................................

6

6.1 Switching Frequency Selection..........................................................................................................................................

6

6.2 Mode Selection..................................................................................................................................................................

6

6.3 VDD Pin Supply Selection..................................................................................................................................................

6

7 Test Procedure

........................................................................................................................................................................

7

7.1 Line and Load Regulation and Efficiency Measurement Procedure..................................................................................

7

7.2 Control-Loop Gain and Phase-Measurement Procedure...................................................................................................

7

7.3 List of Test Points...............................................................................................................................................................

8

7.4 Equipment Shutdown.........................................................................................................................................................

8

8 EVM Assembly Drawing and PCB Layout

............................................................................................................................

9

9 Bill of Materials

.....................................................................................................................................................................

13

10 Revision History

.................................................................................................................................................................

14

www.ti.com

Table of Contents

SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021

Submit Document Feedback

TPS53515 Step-Down Converter Evaluation Module User's Guide

1

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TPS53515





















Reviews: