background image

Connections Descriptions

www.ti.com

4

SLVUBA6 – October 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

TPS1HA08x Evaluation Module

ADVANCE INFORMATION

3

Connections Descriptions

3.1

Connectors and Test Points

Table 1

lists the EVM connector and test point descriptions.

Table 1. Connector and Test Point Descriptions

Connectors and Test Points

Descriptions

T1

High current input terminal for VBB

T2

High current output terminal for VOUT

T3

High current input terminal for GND

VBB_S

Test point used to measure VBB

VOUT

Test point used to measure VOUT

EN

Test point used to apply power to EN, only use when J1 is not connected to 5 V or GND

DIA_EN

Test point used to apply power to DIA_EN, only use when J2 is not connected to 5 V or GND

SEL1

Test point used to apply power to SEL1, only use when J3 is not connected to 5 V or GND

SEL2

Test point used to apply power to SEL2, only use when J3 is not connected to 5 V or GND

ST

Test point used to measure ST

LATCH

Test point used to apply power to LATCH, only use when J7 is not connected to 5 V or GND

SNS

Test point used to measure SNS

LDO_VCC

Test point used to apply power to the 5-V TPS7A1650DGNR LDO, only use when J6 is
disconnected

GND_IC

This is a direct connection to the GND pin of the IC

TP_GND1

This is a connection to the GND plane of the EVM

TP_GND2

This is a connection to the GND plane of the EVM

TP_GND3

This is a connection to the GND plane of the EVM

3.2

Jumpers

Table 2

lists the EVM jumper descriptions.

Table 2. Jumper Descriptions

Jumpers

Description

J1

This jumper is used to connect the EN pin to 5 V (2-3) or GND (1-2)

J2

This jumper is used to connect the DIA_EN pin to 5 V (1-2) or GND (2-3)

J3

This jumper is used to connect the SEL1 and SEL2 pins to 5 V or GND

J4

This jumper connects the ST pin to a 10-k

Ω

pullup resistance

J5

This jumper is used to bypass the ground network used for reverse polarity protection

J6

This jumper is used to power the 5-V TPS7A1650DGNR LDO with the VBB input for the EVM

J7

This jumper is used to connect the LATCH pin to 5 V (2-3) or GND (1-2)

J8

This jumper connects VOUT to an indication LED, showing the user when VOUT is powered

J9

This jumper connects the output of the TPS7A1650DGNR LDO to the 5-V supply net on the EVM

Summary of Contents for TPS1HA08x














Reviews: