background image

Quick Start List for Stand-Alone

2-4

Quick Start

2.3

Quick Start List for Stand-Alone

Follow these steps to use the TPA6100A2 EVM stand-alone or when
connecting it into existing circuits or equipment. Connections to the
TPA6100A2 module header pins can be made via individual sockets,
wire-wrapping, or soldering to the pins, either on the top or the bottom of the
module circuit board. Numbered callouts for selected steps are shown in
Figure 2–2.

Figure 2–2.

Quick Start Module Map

6

2

4

4

5

6

† Due to the very small size of the MSOP IC package, the standard part number TPA6100A2 is

replaced with the code TIAJL.

Power supply

1) Ensure that all external power sources are set to 

OFF.

2) Connect an external regulated power supply set between 1.6 V and 3.3 V

to the module VDD and GND pins taking care to observe marked polarity.

Inputs and outputs

3) Ensure that signal source level is set to minimum and that potentiometers

R1 and R4 are set to the midpoint.

4) Connect the audio source to the module IN1, IN2, and GND pins taking

care to observe marked polarity.

5) Connect the shutdown pin to V

DD

 through a normally open switch.

6) Connect 32-

 headphones to the module V

O

1 and V

O

2 pins through

33-

µ

F to 1000-

µ

F output-coupling capacitors (see Figure 3 – 8) and return

to the GND pin, or

7) For line output, connections to the V

O

1 and V

O

2 pins must be made

through 33-

µ

F to 1000-

µ

F output-coupling capacitors and returned to

GND.

Power-up

8) Verify correct voltage and input polarity and set the external power supply

to 

ON.

The EVM should begin operation.

9) Adjust the signal source level and potentiometers R1 and R4 as needed.

Summary of Contents for TPA6100A2



















Reviews: