manualshive.com logo in svg

Texas Instruments TMS570LC4357, Technical Reference Manual

The Texas Instruments TMS570LC4357 Technical Reference Manual is a comprehensive guide for users looking to maximize the capabilities of their product. This manual can be downloaded for free from manualshive.com, offering detailed instructions and specifications to enhance the user experience and optimize performance.

Share
Download
background image

ADC Registers

www.ti.com

894

SPNU563A – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

Analog To Digital Converter (ADC) Module

Table 22-13. ADC Group 2 Operating Mode Control Register (ADG2MODECR)

Field Descriptions

Field

Value

Description

Reserved

0

Reads return 0. Writes have no effect.

No Reset on ChnSel

No Group2 Results Memory Reset on New Channel Select.

This bit determines whether the group2 results’ RAM is reset whenever a non-zero value is written to
the group2 channel select register.

Any operation mode read/write:

0

Group2 results RAM is reset when a non-zero value is written to group2 channel select register, even if
group2 conversions are completed.

1

Group2 results RAM is not reset when a non-zero value is written to group2 channel select register,
and group2 conversions are completed.

If the group2 conversions are ongoing (active or frozen), then writing a non-zero value to the group2
channel select register will always reset the group2 results RAM.

G2_DATA_FMT

Group2 Read Data Format.

This field is only applicable when the ADC module is configured to be in the 12-bit ADC module. This
field is reserved when the module is configured as a 10-bit ADC module.

This field determines the format in which the conversion results are read out of the group1 results RAM
when using the FIFO interface, that is, when reading from the ADG2BUFFER or ADG2EMUBUFFER
locations.

Any operation mode read/write:

0

Conversion results are read out in full 12-bit format. This is the default mode.

1h

Conversion results are read out in 10-bit format. Bits 11-2 of the 12-bit conversion result are returned
as the 10-bit conversion result.

2h

Conversion results are read out in 8-bit format. Bits 11-4 of the 12-bit conversion result are returned as
the 8-bit conversion result.

3h

Reserved. The full 12-bit conversion result is returned if programmed.

G2_CHID

Enable Channel Id for the Group2 conversion results to be read. This bit only affects the “read from
FIFO” mode. The ADC always stores the channel id in the results RAM. Any 16-bit read performed in
the “read from RAM” mode will return the 5-bit channel id along with the 10-bit conversion result.

Any operation mode read/write:

0

Bits 14-10, the channel id field, of the data read from the Group2 results’ FIFO is read as 00000b.

1

Bits 14-10, the channel id field, of the data read from the Group2 results’ FIFO contains the number of
the ADC analog input to which the conversion result belongs.

OVR_G2_RAM_IGN

This bit allows the ADC module to overwrite the contents of the Group2 results memory under an
overrun condition.

Any operation mode read/write:

0

The ADC cannot overwrite the contents of the Group2 results memory. When an overrun of this
memory occurs, the software needs to read out all the contents of this memory before the ADC is able
to write a new conversion result for the Group2.

1

When an overrun of the Group2 results memory occurs, the ADC proceeds to overwrite the contents
with any new conversion results for the Group2, starting with the first location in this memory.

G2_HW_TRIG

Group2 Hardware Triggered. This bit allows the Group2 to be hardware triggered. The Group2 is
software triggered by default. For more details on how to trigger a conversion group, refer to

Section 22.2.1.6

.

Any operation mode read/write:

0

The Group2 is software-triggered. A Group2 conversion starts whenever the Group2 channel select
register (ADG2SEL) is written with a non-zero value.

1

The Group2 is hardware-triggered. A Group2 conversion starts whenever the Group2 channel select
register has a non-zero value, and the specified hardware trigger occurs. The hardware trigger for the
Group2 is specified in the Group2 Trigger Source register (ADG2SRC).

Summary of Contents for TMS570LC4357

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS570LC4357

ABB 650 series Engineering Manual preview
650 series
Brand: ABB Pages: 128
S&C 6800 Series Instruction Sheet preview
6800 Series
Brand: S&C Pages: 40
QCON ProX Setup preview
ProX
Brand: QCON Pages: 4
A10 Harmony Controller 2000 Installation Manual preview
Harmony Controller 2000
Brand: A10 Pages: 27
Danfoss VLT 2800 Instruction Manual preview
VLT 2800
Brand: Danfoss Pages: 7
Jands SafeGuard Installation Manual preview
SafeGuard
Brand: Jands Pages: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Brand: hager Pages: 34
IFM Electronic ecomat 100 R 360 Operating Instructions Manual preview
ecomat 100 R 360
Brand: IFM Electronic Pages: 16
IFM Electronic AC1331 Installation Instructions Manual preview
AC1331
Brand: IFM Electronic Pages: 23
ZKTeco MA500 Installation Manual & User Manual preview
MA500
Brand: ZKTeco Pages: 20
ZKTeco ProFace X Installation Manual preview
ProFace X
Brand: ZKTeco Pages: 8
ZKTeco TF1600 ZKTeco Quick Start Manual preview
TF1600 ZKTeco
Brand: ZKTeco Pages: 10
ZKTeco SpeedFace-V3L User Manual preview
SpeedFace-V3L
Brand: ZKTeco Pages: 121
ZKTeco FaceDepot-7BL Quick Start Manual preview
FaceDepot-7BL
Brand: ZKTeco Pages: 12
ZKTeco C5S110 Installation And Connection Manual preview
C5S110
Brand: ZKTeco Pages: 6
ZiLOG Z8 Encore! XP Quick Start Manual preview
Z8 Encore! XP
Brand: ZiLOG Pages: 12
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Brand: NEC Pages: 30
Fagor G2-MA Manual preview
G2-MA
Brand: Fagor Pages: 8

Brands by name

Popular brands

Load more brands