manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual

The Texas Instruments TMS320VC5509 Data Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about the product. Explore its features, specifications, and functionalities by downloading the manual from manualshive.com.

Share
Download
background image

Pin Control Register (PCR)

12-41

McBSP Registers

SPRU592E

Table 12

−

11.PCR Bit Descriptions (Continued)

Bit

Field

Value

Description

11

FSXM

Transmit frame-sync mode bit. FSXM determines whether transmit
frame-sync pulses are supplied externally or internally. The polarity of the
signal on the FSX pin is determined by the FSXP bit.

0

Transmit frame synchronization is supplied by an external source via the
FSX pin.

1

Transmit frame synchronization is supplied by the McBSP, as determined
by the FSGM bit of SRGR2.

10

FSRM

Receive frame-sync mode bit. FSRM determines whether receive
frame-sync pulses are supplied externally or internally. The polarity of the
signal on the FSR pin is determined by the FSRP bit.

0

Receive frame synchronization is supplied by an external source via the
FSR pin.

1

Receive frame synchronization is supplied by the sample rate generator.
FSR is an output pin reflecting internal FSR, except when GSYNC = 1 in
SRGR2.

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments

Related manuals for TMS320VC5509

FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
Sangoma A400 Installation Manual preview
A400
Brand: Sangoma Pages: 6
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Brand: Lattice Semiconductor Pages: 13
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Brand: Dahua Pages: 24
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Brand: Opvimus Pages: 12
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
IOtech ADAC/5500MF Installation Manual preview
ADAC/5500MF
Brand: IOtech Pages: 16
Renesas Emulator MCU Board for 38D5 Group M38D59T-RLFS User Manual preview
Emulator MCU Board for 38D5 Group M38D59T-RLFS
Brand: Renesas Pages: 4
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Brand: Seattle Computer Products Pages: 31
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Brand: JUMO Pages: 41
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
Compal KALA0 Schematics Document preview
KALA0
Brand: Compal Pages: 47
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Brand: Hanwha Techwin Pages: 124
Renesas R0E0144TNPFK00 User Manual preview
R0E0144TNPFK00
Brand: Renesas Pages: 4

Brands by name

Popular brands

Load more brands