Texas Instruments TMS320DM335 User Manual Download Page 30 | Manualshive

Page: 30 / 172

background image

4.1.1 ARM Internal Memories

4.1.2 External Memories

4.1.3 Peripherals

Memory Map

www.ti.com

The ARM has access to the following ARM internal memories:

•

32KB ARM Internal RAM on TCM interface, logically separated into two 16KB pages to allow
simultaneous access on any given cycle, if there are separate accesses for code (I-TCM bus) and data
(D-TCM) to the different memory regions.

•

8KB ARM Internal ROM

Note:

By default, ARM access to internal memory is with one wait-state. However, if the ARM clock
frequency is less than or equal to 150 MHz, you may configure ARM access to internal
memory to be zero wait-state. To configure the wait-state use the bit AIM_WAIST in the
Miscellaneous Control register (MISC) in the System Control Module. MISC is described in

Section 9.10.16

The ARM has access to the following external memories:

•

DDR2 / mDDR Synchronous DRAM

•

Asynchronous EMIF/OneNand

•

NAND Flash

•

External host devices

Additionally, the ARM has access to the various common media storage card interfaces.

The ARM and EDMA have access to the registers and memories of the following peripherals (see

•

EDMA Controller

•

Three UARTs

•

I2C (Inter-IC Communication)

•

Three 64-bit timers (each configurable as one 64-bit timer or two 32 bit timers) and one WDT

•

PWM (Pulse Width Modulator)

•

USB (Universal Serial Bus Controller)

•

Two Audio Serial Ports (ASP)

•

Three SPI serial interfaces

•

General-Purpose Input/Output (GPIO)

•

Video Processing Subsystem (VPSS)

•

Asynchronous EMIF (AEMIF) Controller

•

Real Time Out (RTO)

The ARM and EDMA also has access to the following internal peripherals:

•

ETM/ETB

•

ICEcrusher

•

System Module

•

PLL Controllers

•

Power Sleep Controller

•

ARM Interrupt Controller

The ARM and EDMA also has access to the following internal peripherals:

Memory Mapping

30

SPRUFX7 – July 2008

Submit Documentation Feedback

«
...
28
29
30
31
32
...
»

Summary of Contents for TMS320DM335













































































































































































Reviews:

No comments

Related manuals for TMS320DM335

Brand: Asus Pages: 14

Brand: Asus Pages: 12

Aaeon RICO-3288

Brand: Asus Pages: 36

AAEON PICO-APL4

Brand: Asus Pages: 90

Brand: Asus Pages: 102

AAEON PICO-EHL4

Brand: Asus Pages: 108

AAEON PICO-KBU4

Brand: Asus Pages: 93

IAC-H488 Series

Brand: Lanner Pages: 45

Brand: Congatec Pages: 75

Brand: Portwell Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands