Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 538 | Manualshive

Page: 538 / 1141

background image

8.13.3 ADC Interrupt Registers

8.13.3.1 ADC Interrupt Flag Register (ADCINTFLG)

Figure 8-16. ADC Interrupt Flag Register (ADCINTFLG)

15

9

8

Reserved

ADCINT9

R-0

R-0

7

6

5

4

3

2

1

0

ADCINT8

ADCINT7

ADCINT6

ADCINT5

ADCINT4

ADCINT3

ADCINT2

ADCINT1

R-0

R-0

R-0

R-0

R-0

R-0

R-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 8-7. ADC Interrupt Flag Register (ADCINTFLG) Field Descriptions

Bit

Field

Value

Description

15-9

Reserved

0

Reads return a zero; Writes have no effect.

8-0

ADCINTx
(x = 9 to 1)

ADC Interrupt Flag Bits: Reading this bit indicates if an ADCINT pulse was generated

0

No ADC interrupt pulse generated

1

ADC Interrupt pulse generated

If the ADC interrupt is placed in continuous mode (INTSELxNy register) then further interrupt
pulses are generated whenever a selected EOC event occurs even if the flag bit is set.

If the continuous mode is not enabled, then no further interrupt pulses are generated until the user
clears this flag bit using the ADCINTFLGCLR register. The ADCINTOVF flag will be set if EOC
events are generated while the ADCINTFLG flag is set. Both ADCINTFLG and ADCINTOVF flags
must be cleared before normal interrupt operation can resume in non-continuous mode.

Analog-to-Digital Converter (ADC)

538

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

«
...
536
537
538
539
540
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: GE Pages: 2

Brand: Walchem Pages: 10

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: Xilinx Pages: 52

Brand: CORNING Pages: 142

Brand: phytron Pages: 55

Brand: Carel Pages: 36

DYGIZONE GJD910

Brand: GJD Pages: 13

Brand: Allen-Bradley Pages: 162

Driver LED 1x2A/48V

Brand: PXM Pages: 11

Brand: NI Pages: 28

Brand: Hanbay Pages: 13

SetPro MV Series

Brand: Gigarise Pages: 18

Brand: Optelec Pages: 41

DMC-14 5 Series

Brand: Galil Motion Control Pages: 200

Brand: AGS Pages: 12

PLATINE DE SPA SP800

Brand: BWT Pages: 48

Brand: Kelly Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands