manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 987 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 987

www.ti.com

EMAC Registers

987

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Ethernet Controller

15.6.31 EMACTXCNTSCOL Register (Offset = 0x14C) [reset = 0x0]

Ethernet MAC Transmit Frame Count for Frames Transmitted after Single Collision (EMACTXCNTSCOL)

This register maintains the number of successfully transmitted frames after a single collision in the half-
duplex mode.

NOTE:

This counter is reset to all zeros by setting the CNTRST bit in the Ethernet MAC MMC

Control (EMACMMCCTRL).

EMACTXCNTSCOL is shown in

Figure 15-46

and described in

Table 15-55

.

Return to

Summary Table

.

Figure 15-46. EMACTXCNTSCOL Register

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

TXSNGLCOLG

R-0x0

Table 15-55. EMACTXCNTSCOL Register Field Descriptions

Bit

Field

Type

Reset

Description

31-0

TXSNGLCOLG

R

0x0

This field indicates the number of successfully transmitted frames
after a single collision in the half-duplex mode.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments