manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 835 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 835

www.ti.com

Comparator Registers

835

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Analog Comparators

12.5.1 ACMIS Register (Offset = 0x0) [reset = 0x0]

Analog Comparator Masked Interrupt Status (ACMIS)

This register provides a summary of the interrupt status (masked) of the comparators.

ACMIS is shown in

Figure 12-4

and described in

Table 12-6

.

Return to

Summary Table

.

Figure 12-4. ACMIS Register

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

RESERVED

IN2

IN1

IN0

R-0x0

R/W1

C-0x0

R/W1

C-0x0

R/W1

C-0x0

Table 12-6. ACMIS Register Field Descriptions

Bit

Field

Type

Reset

Description

31:3

RESERVED

R

0x0

2

IN2

R/W1C

0x0

Comparator 2 Masked Interrupt Status.
This bit is cleared by writing a 1.
Clearing this bit also clears the IN2 bit in the ACRIS register.

1

IN1

R/W1C

0x0

Comparator 1 Masked Interrupt Status.
This bit is cleared by writing a 1.
Clearing this bit also clears the IN1 bit in the ACRIS register.

0

IN0

R/W1C

0x0

Comparator 0 Masked Interrupt Status.
This bit is cleared by writing a 1.
Clearing this bit also clears the IN0 bit in the ACRIS register.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments