manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 697 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 697

www.ti.com

AES µDMA Registers

697

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Advance Encryption Standard Accelerator (AES)

9.6

AES µDMA Registers

Table 9-21

lists the memory-mapped registers for the AES µDMA. All register offset addresses not listed

in

Table 9-21

should be considered as reserved locations and the register contents should not be

modified.

The AES µDMA interrupt register offsets are relative to the base address 0x44030000.

Table 9-21. AES µDMA Registers

Offset

Acronym

Register Name

Section

0x20

AES_DMAIM

AES DMA Interrupt Mask

Section 9.6.1

0x24

AES_DMARIS

AES DMA Raw Interrupt Status

Section 9.6.2

0x28

AES_DMAMIS

AES DMA Masked Interrupt Status

Section 9.6.3

0x2C

AES_DMAIC

AES DMA Interrupt Clear

Section 9.6.4

Complex bit access types are encoded to fit into small table cells.

Table 9-22

shows the codes that are

used for access types in this section.

Table 9-22. AES µDMA Access Type Codes

Access Type

Code

Description

Read Type

R

R

Read

Write Type

W

W

Write

W1C

1C
W

1 to clear
Write

Reset or Default Value

-

n

Value after reset or the default
value

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments