manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 177 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 177

www.ti.com

FPU Registers

177

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Cortex-M4 Peripherals

2.7

FPU Registers

Table 2-49

lists the memory-mapped registers for the FPU. All register offset addresses not listed in

Table 2-49

should be considered as reserved locations and the register contents should not be modified.

Table 2-49. FPU Registers

Offset

Acronym

Register Name

Section

0xD88

CPAC

Coprocessor Access Control

Section 2.7.1

0xF34

FPCC

Floating-Point Context Control

Section 2.7.2

0xF38

FPCA

Floating-Point Context Address

Section 2.7.3

0xF3C

FPDSC

Floating-Point Default Status Control

Section 2.7.4

Complex bit access types are encoded to fit into small table cells.

Table 2-50

shows the codes that are

used for access types in this section.

Table 2-50. FPU Access Type Codes

Access Type

Code

Description

Read Type

R

R

Read

Write Type

W

W

Write

Reset or Default Value

-

n

Value after reset or the default
value

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments