manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 1661 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1661

www.ti.com

UART Registers

1661

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Universal Asynchronous Receiver/Transmitter (UART)

26.5.20 UARTPeriphID5 Register (Offset = 0xFD4) [reset = 0x0]

UART Peripheral Identification 5 (UARTPeriphID5)

The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset
values.

UARTPeriphID5 is shown in

Figure 26-23

and described in

Table 26-23

.

Return to

Summary Table

.

Figure 26-23. UARTPeriphID5 Register

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

PID5

R-0x0

R-0x0

Table 26-23. UARTPeriphID5 Register Field Descriptions

Bit

Field

Type

Reset

Description

31-8

RESERVED

R

0x0

7-0

PID5

R

0x0

UART Peripheral ID Register [15:8].
Can be used by software to identify the presence of this peripheral.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments