manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1372

I2C Registers

www.ti.com

1372

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Inter-Integrated Circuit (I

2

C) Interface

19.5.24 I2CFIFOCTL Register (Offset = 0xF04) [reset = 0x00040004]

I2C FIFO Control (I2CFIFOCTL)

The FIFO Control Register can be programmed to control various aspects of the FIFO transaction, such
as RX and TX FIFO assignment, byte count value for FIFO triggers and flushing of the FIFOs.

I2CFIFOCTL is shown in

Figure 19-41

and described in

Table 19-31

.

Return to

Summary Table

.

Figure 19-41. I2CFIFOCTL Register

31

30

29

28

27

26

25

24

RXASGNMT

RXFLUSH

DMARXENA

RESERVED

R/W-0x0

R/W-0x0

R/W-0x0

R-0x0

23

22

21

20

19

18

17

16

RESERVED

RXTRIG

R-0x0

R/W-0x4

15

14

13

12

11

10

9

8

TXASGNMT

TXFLUSH

DMATXENA

RESERVED

R/W-0x0

R/W-0x0

R/W-0x0

R-0x0

7

6

5

4

3

2

1

0

RESERVED

TXTRIG

R-0x0

R/W-0x4

Table 19-31. I2CFIFOCTL Register Field Descriptions

Bit

Field

Type

Reset

Description

31

RXASGNMT

R/W

0x0

RX Control Assignment.

0x0 = RX FIFO is assigned to Master

0x1 = RX FIFO is assigned to Slave

30

RXFLUSH

R/W

0x0

RX FIFO Flush. Setting this bit will Flush the RX FIFO. This bit will
self-clear when the flush has completed.

29

DMARXENA

R/W

0x0

DMA RX Channel Enable.

0x0 = DMA RX channel disabled

0x1 = DMA RX channel enabled

28-19

RESERVED

R

0x0

18-16

RXTRIG

R/W

0x4

RX FIFO Trigger. Indicates at what fill level the RX FIFO will
generate a trigger. Programming RXTRIG to 0x0 has no effect since
no data is present to transfer out of RX FIFO.

0x0 = Trigger when RX FIFO contains no bytes

0x1 = Trigger when Rx FIFO contains 1 or more bytes

0x2 = Trigger when Rx FIFO contains 2 or more bytes

0x3 = Trigger when Rx FIFO contains 3 or more bytes

0x4 = Trigger when Rx FIFO contains 4 or more bytes

0x5 = Trigger when Rx FIFO contains 5 or more bytes

0x6 = Trigger when Rx FIFO contains 6 or more bytes

0x7 = Trigger when Rx FIFO contains 7 or more bytes.

15

TXASGNMT

R/W

0x0

TX Control Assignment.

0x0 = TX FIFO is assigned to Master

0x1 = TX FIFO is assigned to Slave

14

TXFLUSH

R/W

0x0

TX FIFO Flush. Setting this bit will Flush the TX FIFO. This bit will
self-clear when the flush has completed.

13

DMATXENA

R/W

0x0

DMA TX Channel Enable.

0x0 = DMA TX channel disabled

0x1 = DMA TX channel enabled

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands