manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1347

www.ti.com

I2C Registers

1347

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Inter-Integrated Circuit (I

2

C) Interface

19.5.6 I2CMRIS Register (Offset = 0x14) [reset = 0x0]

I2C Master Raw Interrupt Status (I2CMRIS)

This register specifies whether an interrupt is pending.

I2CMRIS is shown in

Figure 19-22

and described in

Table 19-12

.

Return to

Summary Table

.

Figure 19-22. I2CMRIS Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

RXFFRIS

TXFERIS

RXRIS

TXRIS

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

7

6

5

4

3

2

1

0

ARBLOSTRIS

STOPRIS

STARTRIS

NACKRIS

DMATXRIS

DMARXRIS

CLKRIS

RIS

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

Table 19-12. I2CMRIS Register Field Descriptions

Bit

Field

Type

Reset

Description

31-12

RESERVED

R

0x0

11

RXFFRIS

R

0x0

Receive FIFO Full Raw Interrupt Status. This bit is cleared by writing
a 1 to the RXFFIC bit in the I2CMICR register.

0x0 = No interrupt

0x1 = The Receive FIFO Full interrupt is pending.

10

TXFERIS

R

0x0

Transmit FIFO Empty Raw Interrupt Status. This bit is cleared by
writing a 1 to the TXFEIC bit in the I2CMICR register. Note that if we
clear the TXFERIS interrupt (by setting the TXFEIC bit) when the TX
FIFO is empty, the TXFERIS interrupt does not reassert even though
the TX FIFO remains empty in this situation.

0x0 = No interrupt

0x1 = The Transmit FIFO Empty interrupt is pending.

9

RXRIS

R

0x0

Receive FIFO Request Raw Interrupt Status. This bit is cleared by
writing a 1 to the RXIC bit in the I2CMICR register.

0x0 = No interrupt

0x1 = The trigger level for the RX FIFO has been reached or there is
data in the FIFO and the burst count is zero. Thus, a RX FIFO
request interrupt is pending.

8

TXRIS

R

0x0

Transmit Request Raw Interrupt Status. This bit is cleared by writing
a 1 to the TXIC bit in the I2CMICR register.

0x0 = No interrupt

0x1 = The trigger level for the TX FIFO has been reached and more
data is needed to complete the burst. Thus, a TX FIFO request
interrupt is pending.

7

ARBLOSTRIS

R

0x0

Arbitration Lost Raw Interrupt Status. This bit is cleared by writing a
1 to the ARBLOSTIC bit in the I2CMICR register.

0x0 = No interrupt

0x1 = The Arbitration Lost interrupt is pending.

6

STOPRIS

R

0x0

STOP Detection Raw Interrupt Status This bit is cleared by writing a
1 to the STOPIC bit in the I2CMICR register.

0x0 = No interrupt

0x1 = The STOP Detection interrupt is pending.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands